IRC POWER SLIDE CONTROL - User Manual

IRC POWER SLIDE CONTROL

18 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

1 di 18

PRESENTS

POWER SLIDE CONTROL

The Power Slide Control is our latest high performance creation; we put down an

enormous amount of time and engineering into it, to create an effective and reliable

product. It is developed by racers for racers.

The Power Slide Control is an electronic system able to reduce the rear wheel slide off

during accelerations and constant throttle. It is not able to reduce the slide off during the

braking phase.

The system is composed by an ECU and 2 velocity sensors put on front and rear wheels.

The variation of the difference between front and rear wheel velocities is continuously

monitored in order to understand if the rear wheel is sliding off or not. The Power Slide

Control is able to understand if the bike is on straight, or in a slow turn or in a fast turn, and

consequently acts.

Please read the installation

instructions carefully before

using your PSC. Make sure

you fully understand and

agree with disclaimer

before using this product.

Table of Contents

Questions and Answers

H
hpalmerAug 5, 2025
What to do if my IRC POWER SLIDE CONTROL system is NOT WORKING (Fixed green light)?
- J
  Jennifer MuellerAug 5, 2025
  If your IRC Motorcycle Accessories system shows a fixed green light and is not working, switch the system off and on. If the problem continues, DO NOT USE the system.
D
Douglas GoodwinAug 14, 2025
What to do if my IRC POWER SLIDE CONTROL Motorcycle Accessories system is NOT WORKING (No flash)?
- B
  Brittany WilsonAug 14, 2025
  If your IRC Motorcycle Accessories system has no flash and is not working, switch the system off and on. If the issue persists, DO NOT USE the system.
H
hvegaAug 25, 2025
How to activate the IRC Motorcycle Accessories system if it's OFF (Constant blinking flash, like an arrow)?
- L
  lwilliamsAug 25, 2025
  To activate your IRC Motorcycle Accessories system, select a “Sensitivity” different from “0” by moving the knob clockwise.

Summary

Product Introduction

Disclaimer and Warnings

General Warnings

Crucial warnings about product use, modification, and installation.

Installation Manual

Sensors Installation

Guide for fitting and connecting front and rear speed sensors correctly.

Ground Connection

Procedure for connecting the system's ground wire to the frame.

Coils;Injectors Connection

How to connect the PSC to motorcycle ignition coils or injectors.

Japanese Sports Bike & Triumph Coil Wiring

Specific wiring for Denso and Mitsubishi ignition systems on sport bikes.

Ducati, Aprilia, MV Coil Wiring

Wiring instructions for specific European motorcycle models.

KTM SuperDuke & RC8 Coil Wiring

Specific installation notes for KTM models.

Aprilia Twin Spark Engine Wiring

Wiring for Aprilia models with twin spark engines.

Injectors Connection

Steps for connecting the PSC to motorcycle injectors.

MV Injector Wiring

Specific wiring for MV Agusta models.

System Setup and Configuration

Setting Pulses and Ratio

Configuring sensor pulses and wheel speed ratio via selector switches.

Dashboard Installation

Instructions for mounting the potentiometer, switches, and LEDs.

Control Switches and Functions

Operation of Launch Control, TC, and emergency switches.

Pre-Use Checks and Troubleshooting

Pre-Use System Checks

Essential tests to perform before operating the system.

Diagnosis and Error Indicators

Understanding red LED error codes and diagnosis button function.

Status LED (Green)

Interpreting green LED status and troubleshooting operational issues.

Green Light Issues

Troubleshooting when the green LED flashes but PSC does not cut.

Sensor Verification

Procedures to verify proper sensor function and reading.

Other Troubleshooting

Common issues and their resolutions.

Telemetry Systems

Instructions for connecting to data acquisition systems.

IRC POWER SLIDE CONTROL Specifications

General

Brand	IRC
Model	POWER SLIDE CONTROL
Category	Motorcycle Accessories
Language	English