Ithaca 150 - Index

Programmer's Guide PcOS Series 150 Index
12/14/99 Rev G Page 137
Index
—[—
[CAN] Clear print buffer........................................54
[CR] New line .......................................................15
[DC2] Set 10 cpi....................................................31
[DC4] End one-line double-wide............................33
[ENQ] <1> Inquire Cash Drawer 1 status...............60
[ENQ] <10> Request printer reset..........................62
[ENQ] <11> Request printer power-cycle status.....62
[ENQ] <2> Inquire Cash Drawer 2 status...............60
[ENQ] <4> Inquire receipt-paper out status............60
[ENQ] <6> Inquire form position sensor status.......61
[ENQ] <7> Inquire form-clamp status....................61
[ENQ] <9> Send response .....................................61
[ENQ] <n> Inquire printer status ...........................60
[ESC] - <0> End underline ....................................35
[ESC] - <1> Begin underline .................................35
[ESC] ! <n> Select international character set........24
[ESC] # <0> Begin High Speed Draft Mode...........22
[ESC] $ Copy ROM Character Set to RAM Character
Set ....................................................................28
[ESC] % G Begin italics........................................37
[ESC] % H End italics...........................................38
[ESC] * <m> <n>
1
<n>
2
Print graphics in mode <m>
.........................................................................45
[ESC] \: Set 12 cpi.................................................31
[ESC] ? <m><n> Reassign graphics mode..............45
[ESC] [ @ ... Double-high, double-wide, and italic 34
[ESC] [ C <n> Insert Euro Character......................29
[ESC] [ P <n> Set cpi ............................................32
[ESC] [ S <L
L
> <L
H
> <B
C
> … Redefine Character
Set ....................................................................27
[ESC] [ T <n
h
> <n
l
> Select Character Code Page ..26
[ESC] [DC1] Open forms clamp.............................51
[ESC] [DC3] Close forms clamp ............................51
[ESC] [DC4] Select validation mode......................51
[ESC] [EM] B 0 Bar code height............................49
[ESC] [EM] C <0> Validation clamp delay............52
[ESC] [EM] J <n> Bar code justification................49
[ESC] [EM] V <n> Set validation delay.................52
[ESC] [SI] Set 24 cpi .............................................31
[ESC] ] Reverse line feed.......................................21
[ESC] ^ <n> Print control character .......................27
[ESC] _ <0> End overscore....................................35
[ESC] _ <1> Begin overscore.................................35
[ESC] ~ <n> Extended diagnostics.........................66
[ESC] < <n> Pass through......................................56
[ESC] < <n> Print suppress ...................................56
[ESC] = <c1><c2><start code><data> Character
download...........................................................28
[ESC] > <0> Custom character set OFF .................29
[ESC] > <1> Custom character set ON...................28
[ESC] 0 Set line space to 27/216 inch ....................18
[ESC] 1 Set line spacing 7/72 inch.........................19
[ESC] 2 Enable variable line spacing......................19
[ESC] 3 <n> Set line spacing in n/216 inch ............18
[ESC] 4 Set top of form..........................................20
[ESC] 5 <0> End auto line feed..............................21
[ESC] 5 <1> Begin auto line feed...........................21
[ESC] 8 Disable PE sensor.....................................50
[ESC] 9 Enable PE sensor......................................50
[ESC] a <n> Set justification..................................17
[ESC] A <n> Set variable line spacing n/72 inch ....19
[ESC] b <n> ... Print bar code ................................47
[ESC] B <n>1 <n>2 Set vertical tab stops ..............20
[ESC] C Set form length........................................21
[ESC] C [NUL] Set form length.............................21
[ESC] d <n> Enable variable line spacing...............19
[ESC] D <n>1 <n>2 Set horizontal tab stops ..........16
[ESC] E Begin emphasized print ............................36
[ESC] F End emphasized print ...............................36
[ESC] G Begin enhanced print ...............................36
[ESC] H End enhanced print ..................................36
[ESC] I <1> Set Utility Print Mode ........................22
[ESC] J <n> Fine line feed.....................................18
[ESC] K <n>
1
<n>
2
Print single-density graphics....44
[ESC] L <n>
1
<n>
2
Print double-density graphics ...44
[ESC] P <0> Reset 90° rotated font........................23
[ESC] P <1> Set 90° rotated font............................23
[ESC] P <2> Set 270° rotated font..........................23
[ESC] q <n> Query marker.....................................55
[ESC] r <0> End rotated print ................................42
[ESC] r <1> Rotate 90°..........................................40
[ESC] r <2> Rotate 180° ........................................41
[ESC] r <3> Rotate 270° ........................................41
[ESC] r <5> Rotate 90° with line formatting...........40
[ESC] r <7> Rotate 270° with formatting................41
[ESC] R Reset horizontal tab stops.........................17
[ESC] s <n> Set rotated print line length................42
[ESC] S<0> Select superscript ...............................37
[ESC] S<1> Select subscript ..................................37
[ESC] T End superscript or subscript......................37
[ESC] U <0> Begin bidirectional print ...................46
[ESC] U <1> Begin unidirectional print .................46
[ESC] u <n
1
> <m
1
>… Set rotated print line spacing43
[ESC] V <n> Set intercharacter spacing..................32
[ESC] W <n> Double-wide and double-high...........34
[ESC] w <n> Enable dynamic response ..................57
[ESC] x <n> Open cash drawer ..............................54
[ESC] X <n1> <n2> Set left/right margin...............53
[ESC] y <n> Feature control...................................56
[ESC] Y <n>
1
<n>
2
Print full-speed double-density
graphics.............................................................44
[ESC] Z <n>
1
<n>
2
Print quad-density graphics......45
[ESC]v Activate cutter............................................57
[FF] Form feed.......................................................20
[HT] Horizontal tab................................................16
[LF] Line feed........................................................15
[SI] Set 17 cpi........................................................31