Jacobsen TR3 EJ Series

To Next Page

To Previous Page

en-5

MADE IN U.K.

A.B.T. PRODUCTS LTD.

ROSS-ON-WYE,

HEREFORDSHIRE,

HR9 7BW

TEL: (01989) 563653

LMAC 164

### - ##

INTRODUCTION 2

ROPS Serial Plate

ROPS Serial Plate Location

The ROPS serial plate (C) is located at the base of the of the ROPS main

left hand beam.

Main Page

Table of Contents2
Introduction 23
Important3
Product Identification4
Guidelines for the Disposal of Scrap Products6
During Service Life6
End of Service Life6
Parts Manual7
Key Numbers7
Safety8
How to Operate Safely8
Safe Operation8
Preparation8
Operation9
Rops10
Safe Handling of Fuels10
Maintenance and Storage10
When You Put a Mower on a Trailer11
Important Safety Notes12
Specifications15
Engine Specification15
Machine Specification15
Dimensions15
Vibration Level16
Noise Emissions17
Cutting Unit Specification18
Recommended Lubricants19
Cutting Performance (Area)19
Conformity Certificates20
Decals24
Safety Decals EC24
Instruction Decals EC24
Safety Decals USA25
Instruction Decals USA25
Controls26
Instrument Panel26
Starter Key Switch27
Parking Brakes27
Working Light Switch27
Cutting Unit Switch27
Weight Transfer Switch28
Blocked Hydraulic Filter Indicator Lamp28
Throttle Control Lever29
Joystick Unit Lift/Lower Control29
Multi-Function Gauge30
Traction Foot Pedal31
Power Outlet31
Steering Tilt Control31
Parking Brake Release Valve32
Transport Latches32
Operation 733
Daily Inspection33
Operator Presence and Safety Interlock System34
Operating Procedure35
Fitting the Cutting Units to the Machine36
Starting the Engine37
Driving37
Mowing37
To Stop the Engine37
Transporting38
Transporting on a Trailer or Flatbed39
Mowing on Slopes40
Maintenance and Lubrication44
Maintenance & Lubrication Chart44
Cutting Unit Lmac194/195/196/197 Lubrication46
Cutting Units 47114, 47115, 47116 Lubrication47
Engine Lubrication48
Engine: Fan Belt48
Engine Coolant49
Hydraulic System50
Hydraulic Test Ports51
Fuel System52
Air Cleaner53
Battery53
Machine Maintenance54
Freewheel Control54
Adjustments 955
Traction Control Pedal55
Weight Transfer Adjustment55
Cutting Units Lmac194 / 195 / 196 / 19756
Height of Cut56
To Set Rear Roll56
To Set Height of Cut56
Reel to Bedknife Adjustment57
Reel Bearings57
Front and Rear Roll Bearings57
Cutting Units 47114, 47115, 4711658
Reel-To-Bedknife (Pre-Adjustment Check)58
Reel-To-Bedknife Adjustment59
Cutting Modes60
Cutting Height - Fixed Mode61
Cutting Height - Floating Mode62
Speed Limiter63
Seat (Milsco CE-9.16 Seat (Michigan V-5300)64
General Instructions for Grammer Seats65
Seat (Grammer MSG85)67
Weight Adjustment68
Fore/Aft Adjustment68
Air Suspension Seat (Grammer MSG75 -521)68
Backrest Extension69
Seat Heater69
Lumbar Support69
Armrests70
Armrest Adjustment70
Backrest Adjustment70
Maintenance71
Backlapping Kit (Lmac161)72
Ops Frame (Lmac164)73
Transport Latch Kit (Lmac174)73
Working Lamp Kit (Lmac163)73
Grass Box Kit (Lmac182 )73
Grass Box Kit (Lmac193 )73
Problem Solving74
Engine General74
Quality of Cut Problem Solving75
Washboarding75
Marcelling76
Step Cutting77
Scalping78
Stragglers79
Streaks80
Windrowing81
Rifling or Tramlining82
Mismatched Cutting Units82
Schematics84
Hydraulic Circuit84
Electrical Circuit Instrument86
Electrical Circuit Main88
Electrical Circuit Fuses and Relays90
Torques92

Jacobsen TR3 EJ Series

Table of Contents

Related product manuals