Jacuzzi J-435 - Water Care Programming

60
has been manually turned on, it will automatically turn off after
approximately 20 minutes. If at this time you desire more jet oper-
ation you may simply turn the pump(s) back on.
QLights Menu:
From the Home Menu, tap (
) to enter the Light submen-
us. The LCD screen will display the Light Submenu. From this
menu you can control the hot tub lighting. When you tap ( )
to enter the submenus, the lights will turn on, if not on already,
in a color blending mode. Default settings are brightness level
at 0 and speed setting of 0.
Note: The lights automatically turn off after 2 hours. They can be
reactivated if needed.
Brightness Up Button: Tap to raise the intensity of
the lights to the maximum level of 5. The intensity lev-
els are as follows: 5 = 100%, 4 = 80%, 3 = 60%, 2 = 40%
and 1 = 20%, 0 = 0%.
Brightness Down Button: Tap to lower the intensity
of the lights to the minimum level of 0.
Intensity Indicator: Displays the current intensity lev-
el of the lights by the number of bars filled in. This will
only work with the solid color option. If the blending
mode is on, the light bulb is grayed out. The range is
from 0 to 5.
Speed Control Button (Increase): Tap to increase the
blending speed, of the colors, to the maximum speed
of 5. The speed settings are as follows: 5 = every 5
secs, 4 = every 10 secs, 3 = every 15 secs, 2 = every 30
secs and 1 = every 60 secs.
Speed Control Button (Decrease): Tap to decrease
the blending speed, of the colors, to the minimum
speed of 0.
Speed Selector Icon: Tap
or to select the
blending speed for the light colors.
Color Selector: Tap a color to select a single color.
Back Button: Tap to go back to the previous menu.
Invert Button: Tap to invert the display image.
External light button: press once to turn the lights
on (high intensity). Press the button again to reduce
the intensity and again to turn the lights off. The
lights (white only) remain on for a maximum of 8
hours (where not switched off before as specified
above). When turned on for the first time, they flash to
indicate that there is a connection.
QMusic Menu
Models equipped with the optional Audio System offer an
enhanced spa experience. The BLUEWAVE 2.0 Wireless Audio
System works with most Bluetooth wireless devices. An auxil-
iary device can be connected, via a 3.5 mm plug cable, located
behind the front cabinet panel, if a Bluetooth device is not avail-
able. These models also include four high fidelity spa engineered
speakers for unsurpassed sound quality and long-life, and an
integrated powered subwoofer for a superb acoustical sound.
Note: If the spa does not have the stereo option, there will not be
a button on the control panel.
To access the Music Menu, tap ( ). Once you enter the Music
Menu, tap the power button to turn the stereo on. Your con-
nected electronic device, Bluetooth or auxiliary, provides the
audio entertainment.

RISK OF ELECTRICAL SHOCK HAZARD EXISTS AND
EQUIPMENT DAMAGE! Never install or remove electri-
cal devices while hands are wet or while sitting partial-
ly immersed or fully immersed in spa!
100
6:45p
Track Name
MUSIC
Vol: 30
Power Button: Tap to turn the stereo on and off.
Bluetooth Settings: Tap to use your Bluetooth device
with the stereo. This is the default setting.
Auxiliary Settings: Tap to use your auxiliary device
with the stereo.
Volume Up: Tap to increase the volume. The range is
from 0 to 30 increments of 1.
Volume Down: Tap to decrease the volume. The range
is from 0 to 30 increments of 1.
Forward: Tap to advance forward through tracks.
Rewind: Tap to move back through tracks.
Pause/Play: Tap to pause and play tracks.
Artist Track: Will display the artist and track infor-
mation, if it is available. If the information is not
available this part will be blank. If the information
provided is too long, the maximum number of
100
6:45p
LIGHTS
Speed: 1
Speed: 1
or
Track Name