To Next PageTo Next Page
Need help?Do you have a question about the Jandy LG125 and is the answer not in the manual?
General| Model | LG125 |
|---|---|
| Category | Swimming Pool Heater |
| Heating Capacity | 125, 000 BTU/hr |
| Heat Exchanger | Copper |
| Efficiency | 82% |
| Minimum Flow Rate | 20 GPM |
| Maximum Working Pressure | 50 PSI |
| Fuel Type | Natural Gas or Propane |
| Ignition | Electronic |
Product installation and operation safety guidelines, including carbon monoxide risks.
Immediate actions to take if a gas leak is detected to prevent fire or explosion.
Provides installation and operation instructions for the Lite2 Model LG pool and spa heater.
Details safe and reliable service, including warnings and cautions.
Details the limited factory warranty, claim procedures, and exclusions.
Lists certifications, local codes, and national installation codes for gas fired pool heaters.
Provides contact information for Jandy technical support and distributors for assistance.
Lists materials the installer must supply for all installations and special installations.
Details technical specifications including location, gas type, pressure, flow rate, and dimensions.
Details installation procedures, local codes, and national codes for proper heater installation.
Describes procedures for assembling the heater components in the field, including drafthood installation.
Specifies requirements for heater placement, clearances, flooring, and outdoor/shelter installations.
Details requirements for sufficient air supply for proper combustion and ventilation of the surrounding area.
Covers vent pipe sizing, installation for outdoor and indoor/shelter setups, and replacement.
Provides instructions on gas supply, piping, sediment traps, shutoff valves, and pressure testing.
Explains how to confirm and adjust manifold gas pressure for natural gas and LP heaters.
Details specific safety precautions and installation requirements for LP gas.
Illustrates typical piping, shutoff valve restrictions, and pressure switch adjustment considerations.
Explains the importance of a check valve to protect against back-siphoning and dry starts.
Describes the automatic flow control valve and its function in maintaining proper heater flow.
Provides procedures for switching the water connections to the opposite side of the heater.
Details how to connect threaded iron pipe, copper pipe, and plastic piping to the heater.
Recommends and explains the installation of a pressure relief valve for safety and code compliance.
Warns about material compatibility with chemicals and ozone, and proper installation of feeders.
Explains that the heater does not require external electrical power, operating on millivolts from a thermopile.
Details the requirement to connect the heater to a bonding grid with a solid copper wire.
Provides instructions for wiring a time clock to control filter pump operation and the heater.
Describes the automatic operation cycle based on water flow and preset temperature settings.
Provides critical safety warnings and procedures for starting the heater for the first time or after maintenance.
Outlines step-by-step instructions for lighting the pilot and shutting down the main burners and heater.
Explains how to use the ON/OFF switch and rotary dial for temperature adjustment.
Details how to adjust the water pressure switch to ensure proper safety and operation.
Describes how to perform a temperature rise test to confirm proper water flow and heater operation.
Provides procedures for adjusting a manual bypass valve to optimize temperature rise.
Explains the importance of proper water chemistry for spa and pool heaters and lists recommended levels.
Covers procedures for seasonal operation, including spring/fall and winterizing the heater.
Recommends periodic inspections and basic safety checks for safe and efficient operation.
Provides general tips for common problems, causes, and solutions encountered during first-time use or start-up.
A table listing symptoms, causes, and remedies for various heater operational issues.
Emphasizes that service must be performed by a qualified technician and owner checks.
Illustrates and explains the atmospheric combustion system of the Lite2 LG pool heater.
Describes key components like gas valve, temperature control, pilot, limit switches, etc.
Provides procedures for checking pilot generator, controls, and wiring for electrical faults.
Provides instructions on how to order or purchase parts for the Lite2 model LG pool/spa heater.
Contains a list of parts, general exploded view, and detailed exploded views for identification.
Diagram showing the assembly of various heater components with part numbers.
Detailed diagrams illustrating the assembly of specific heater components for part identification.
