Need help?Do you have a question about the Jandy PRO Series JXI260 and is the answer not in the manual?
General| Model | JXI260 |
|---|---|
| Category | Swimming Pool Heater |
| BTU Input | 260, 000 BTU |
| Efficiency | 84% |
| Minimum Flow Rate | 30 GPM |
| Maximum Flow Rate | 120 GPM |
| Heat Exchanger | Cupro-nickel |
| Gas Type | Natural Gas or Propane |
| Water Connections | 2 in |
General safety instructions for proper installation and operation, emphasizing risks of injury or death.
Step-by-step instructions on what to do if you smell gas, including immediate actions and contacting authorities.
Requirement for installation and service to be performed by licensed and qualified professionals.
Importance of proper chemical balances for sanitary bathing and heater lifespan.
Recommended schedule for changing spa water based on usage.
Heater warranty is voided by damage from corrosive chemical levels or excess dissolved solids.
Details the location of the model and serial number on the heater's front panel.
Specifies minimum clearance required from the heater to a door panel.
Specifies the minimum vertical clearance required above the heater.
Specifies the minimum clearance required from the heater header for service.
Minimum clearances required from the heater to combustible surfaces.
Minimum clearances required for accessing the heater for service.
Specifies minimum distance from the heater to a door for outdoor installation.
Clearance requirements between the heater top and a vented opening.
General venting requirements according to the National Fuel Gas Code.
Instructions for installing a 4" double-wall appliance adapter for Category I venting.
Instructions for installing vent connectors or elbows for Category III venting.
Clearance requirements for vent termination relative to objects.
Description of required air supply for indoor installations.
Illustration of side wall vent terminals for Category III installations in the USA.
Reference to CSA B149 for specific Canadian side wall venting requirements.
Recommendation for a specific Z-vent part number.
Requirement for outdoor air openings for combustion and ventilation in indoor installations.
Details on required permanent air supply openings based on ANSI standard.
Information on net free area requirements for outdoor air supply openings.
Guidance on PRV recommendation, requirements, and supply status.
Specifies the maximum working pressure for the heater.
Details compliance standards for installed PRVs in the US and Canada.
Restrictions on using flexible gas piping and restrictive gas cocks.
Instructions for installing sediment traps and unions ahead of gas controls.
Information on factory wiring and options for 120V or 240V operation.
Procedure to change the voltage selector board for 120V operation.
Requirement to follow National and Canadian Electrical Codes for wiring.
Caution to avoid abrading or damaging wiring and components.
Electrical wiring must comply with NEC® and CEC standards.
Advice to take care not to abrade or damage wiring or components.
Specific connections for hot and neutral wires of a 120V power supply.
Warning that the heater lacks a pilot light and should not be lit manually.
Instruction to press the POOL button to activate the pool thermostat.
Instruction to press the SPA button to activate the spa thermostat.
Use UP and DOWN buttons to select pool and spa functions.
Press MENU button to access setup and programming for pool and spa.
Electrical wiring must follow NEC/CEC; take care with components.
Instructions for setting heater control for remote TSAT 2-Wire connection.
Prevents burner firing if water flow to heater is restricted.
Monitors heat exchanger temperature to prevent overheating.
Controls heater operation to attain and maintain selected water temperature.
Prevents igniter firing if there is inadequate vacuum in the blower.
Provides pre-purge, opens gas valve, and monitors flame for safety.
Heater includes the Zodiac® Sweep Elbow for improved performance.
Installation provides increased hydraulic performance.
Exclusive interface compatibility with Zodiac AquaLink® RS temperature sensor.
Heater must be fastened to equipment pad in high-risk weather areas.
Specifies the part number for the Anchor Brackets Kit.
To Next Page
