Need help?Do you have a question about the Jandy PRO Series JXI200 and is the answer not in the manual?
General| Brand | Jandy |
|---|---|
| Model | PRO Series JXI200 |
| Category | Swimming Pool Heater |
| Language | English |
Introduces the JXi Gas-Fired Pool and Spa Heaters and lists available models: JX1200, JXI260, JX1330, JX1400.
Provides essential safety warnings regarding fire, explosion, and CO hazards, plus gas leak response steps.
Stresses that installation and maintenance must be performed by qualified and licensed professionals.
Details ideal chemical parameters for pools and spas, including chlorine, bromine, pH, alkalinity, and hardness.
Guides users on how to find the heater's model number and serial number on the rating plate.
Illustrates minimum clearance distances from doors, vertical space, and service access points for safe installation.
Specifies required clearances (inches/cm) for combustible surfaces and service access around the heater.
Details required distances from the heater to doors and vented openings for outdoor installations.
Defines the minimum safe distance from the heater to the inside wall of the pool for outdoor setups.
Provides vent size specifications for Category I and Category III indoor installations based on specific heater models.
Illustrates required clearances for vent termination points in indoor Category I (US) and outdoor shelter (CAN) installations.
Details clearances for side wall vent terminals for Category III (USA) and Canadian installations, including suggested vent type.
Specifies the minimum net free area required for air supply openings for indoor installations, direct or ducted.
Provides recommended gas pipe sizes based on distance from the gas meter and heater BTU input rate.
Details acceptable maximum and minimum gas supply pressures for natural gas and propane, and gas offset.
Illustrates the connection of a digital manometer to the gas valve for pressure testing, showing ports and connections.
Explains the recommendation and requirements for PRV installation and lists the components included in the PRV R-KIT.
Demonstrates correct and incorrect methods for installing a gas line sediment trap and union, emphasizing placement.
Details the procedure for adjusting the voltage selector board to enable 120V operation for the heater.
Provides instructions for safely connecting the 120V or 240V power supply wires to the heater leads.
Step-by-step guide with diagrams showing how to open the heater to access internal electrical components.
Outlines the sequence of operations from water temperature reading to burner ignition and continuous heating.
Explains the function of each button on the heater's control panel: POOL, SPA, MENU, UP, and DOWN.
Provides a visual guide on how to navigate the menu to select and set the user interface display language.
Details the procedure to toggle and set the temperature display between Fahrenheit (°F) and Celsius (°C) units.
Explains how to set the display backlight timeout options, including 2 MIN TIMEOUT, LIGHT OFF, and LIGHT ON.
Guides users on how to turn on the pool or spa heating function and set the initial target temperature.
Describes how to set and maintain the desired temperature for the pool or spa heat functions.
Details the method to lock or unlock the temperature set point to prevent unauthorized changes.
Provides instructions for wiring remote control systems, such as Aqualink® RS, to the heater's remote control terminal.
Step-by-step guide to set up a 2-wire remote thermostat, including setting it to maximum temperature for operation.
Lists common control panel messages and their associated faults to aid in troubleshooting.
A table correlating temperature readings (°F/°C) with the corresponding resistance (Ohms) of the temperature sensor.
Explains the function of key safety components: Water Pressure Switch, High Limit Switches, Temperature Sensor, Air Flow Switch, Ignition Control.
A diagram labeling the various parts of the header assembly, including the flow plate, sensor, and switches.
Step-by-step instructions with visuals for removing and replacing the Thermal Regulator Valve (TRV).
Illustrates the internal heat exchanger tube configurations for the JX1400 and JX1260 models.
Highlights features of the optional Versa Plumb® ready piping, including the Sweep Elbow and AquaLink® RS temperature sensor interface.
Shows the heater's design for direct drop-in replacement of Pentair® MasterTemp® models, indicating inlet/outlet ports.
Details the requirement and process for securely fastening the heater to the equipment pad using anchor brackets.
Presents a comprehensive wiring diagram for the heater, including a key for wire colors and terminal connections.
Provides contact phone numbers and website addresses for technical support in the USA and Canada.
To Next Page
