Janome MEMORY CRAFT 9700 User Manual (English)

Other manuals for Janome MEMORY CRAFT 9700

Questions and Answers:

Z
Zachary MitchellAug 15, 2025
Why is my Janome MEMORY CRAFT 9700 Sewing Machine needle breaking?
- M
  Michael WagnerAug 15, 2025
  The needle of your Janome Sewing Machine might be breaking due to several reasons: * The needle may be inserted incorrectly. * The needle might be bent or blunt. * The needle clamp screw could be loose. * The needle thread tension might be too tight. * The fabric may not be drawn to the rear when sewing is finished. * The needle could be too fine for the fabric being sewn.
R
Ronald RodriguezAug 18, 2025
Why does my Janome MEMORY CRAFT 9700 make strange sounds when I switch it on?
- A
  ashley59Aug 18, 2025
  If your Janome Sewing Machine is making strange sounds when switched on, it could be because: * Something is caught between the carriage and the arm; in this case, remove the object. * The carriage is touching something around the machine.
C
Cassandra KellyAug 21, 2025
Why does the needle thread keep breaking on my Janome MEMORY CRAFT 9700?
- M
  Miss Jessica ConwayAug 21, 2025
  There are several reasons why the needle thread might break on your Janome Sewing Machine: * The needle thread may not be threaded properly. * The needle thread tension might be too tight. * The needle could be bent or blunt. * The needle might be inserted incorrectly. * The thread could be too heavy for the needle. * The needle thread may not have set in the thread holder when embroidery sewing started.
B
briannahooperAug 25, 2025
Why is the cloth not feeding smoothly through my Janome Sewing Machine?
- K
  Katherine PerkinsAug 25, 2025
  If your Janome Sewing Machine's cloth isn't feeding smoothly, it could be due to: * The feed dog being packed with lint. * The presser foot pressure being too weak. * The stitches being too fine; try making stitches coarser. * The fabric not being fed when sewing is starting. * The feed dog being lowered. * The incorrect presser foot being used.
D
david01Aug 27, 2025
Why is the bobbin thread breaking on my Janome MEMORY CRAFT 9700 Sewing Machine?
- A
  Alexander SmithAug 27, 2025
  Here are a few reasons why the bobbin thread might be breaking on your Janome Sewing Machine: * The bobbin thread may not be threaded properly in the bobbin holder. * Lint may have collected in the bobbin holder. * The bobbin might be damaged and doesn’t turn smoothly; in this case, replace the bobbin.
R
Roger JenningsAug 30, 2025
Why is my Janome Sewing Machine causing seam puckering?
- L
  Lisa SpencerAug 30, 2025
  Seam puckering on your Janome Sewing Machine can occur for several reasons: * The needle tension might be too tight. * The needle thread or the bobbin thread may not be threaded correctly. * The needle could be too heavy for the fabric being sewn. * The stitch length might be too long for the fabric; try making stitches denser. * The presser foot pressure may not be adjusted correctly; when sewing extremely lightweight materials, place interfacing underneath the fabric. * The fabric may not be pulled tightly enough on the embroidery hoop.
M
matthewriosSep 2, 2025
Why is the fabric slipping when I use my Janome Sewing Machine?
- L
  Lisa FloresSep 2, 2025
  If the fabric is slipping while using your Janome Sewing Machine, it could be due to: * The presser foot pressure not being adjusted correctly. * The correct presser foot not being used.
S
Shawn SampsonSep 5, 2025
Why are the patterns distorted on my Janome MEMORY CRAFT 9700?
- B
  brittany77Sep 5, 2025
  If the patterns on your Janome Sewing Machine are distorted, it could be due to: * The correct presser foot not being used. * The needle thread tension being too light. * The stitch length not being suitable for the fabric being sewn. * The feed balancing dial not being properly set. * Interfacing not being used for sewing stretch and very fine fabrics; use an interfacing. * The embroidery hoop Attaching Knob being loose. * The carriage bumping into something around the machine. * The fabric not being pulled tightly enough on the embroidery hoop. * The fabric being caught or pulled for some reason when sewing embroidery; stop the machine and free the fabric.
L
Linda WrightSep 8, 2025
Why are the automatic buttonhole stitches not balanced on my Janome MEMORY CRAFT 9700 Sewing Machine?
- M
  Mrs. Dana MoralesSep 8, 2025
  The automatic buttonhole stitches on your Janome Sewing Machine may not be balanced because: * The stitch length is not suitable for the fabric being sewn. * The feed balancing dial is not set properly. * Interfacing is not used with stretch fabric; use an interfacing.
J
John TorresSep 12, 2025
Why don't the pattern selection keys work on my Janome Sewing Machine?
- A
  Andrea CummingsSep 12, 2025
  The pattern selection keys on your Janome Sewing Machine may not work because: * The bobbin winder spindle is in the winding position. * The control circuit is not working correctly; turn the switch off and turn it on again. * The key position is out of alignment.

Janome MEMORY CRAFT 9700 Specifications

General

Type	Computerized Sewing and Embroidery Machine
Maximum Stitch Width	7 mm
Maximum Stitch Length	5 mm
Built-in Fonts	3
Display	LCD Touch Screen
USB Connectivity	Yes
Built-in Embroidery Designs	100
Needle Threader	Automatic
Presser Feet	7
Memory	Yes
Bobbin System	Drop-in