Janome HORIZON Memory Craft 9480 QC PROFESSIONAL User Manual (English)

Questions and Answers:

A
amberwareAug 13, 2025
Why is my Janome HORIZON Memory Craft 9480 QC PROFESSIONAL skipping stitches?
- E
  Eddie OnealAug 14, 2025
  If your Janome Sewing Machine is skipping stitches, it could be due to several reasons. The needle might be incorrectly inserted, bent, or blunt. The needle and/or threads may not be suitable for the fabric, or a poor-quality needle might be in use. Ensure the needle thread is threaded properly. For stretch, very fine, and synthetic fabrics, use a blue tip needle. For thick fabrics, denims, and sewing across hems, use a purple tip needle. In any of these cases, changing the needle is recommended.
M
melanie92Aug 17, 2025
What to do if the needle breaks on my Janome HORIZON Memory Craft 9480 QC PROFESSIONAL Sewing Machine?
- C
  Charles AlvarezAug 17, 2025
  If the needle breaks on your Janome Sewing Machine, several factors could be at play. The needle might be incorrectly inserted or bent. The needle clamp screw could be loose, or the needle might be too fine for the fabric you're using. Additionally, using an inappropriate presser foot or pulling the fabric when sewing free motion quilting with an open-toe foot can cause the needle to break. In all of these cases, changing the needle is recommended, except when an inappropriate presser foot is used, in which case you should use the correct foot.
A
Andrew CoxAug 21, 2025
How to fix a Janome HORIZON Memory Craft 9480 QC PROFESSIONAL when the bobbin thread breaks?
- G
  greentraceyAug 21, 2025
  If the bobbin thread breaks on your Janome Sewing Machine, check if the bobbin thread is threaded properly in the bobbin holder. Also, lint may have collected in the bobbin holder, or the bobbin itself might be damaged and not turning smoothly. In all of these cases, changing the bobbin is recommended.
J
Jenny WilliamsAug 25, 2025
What causes loops on the seams when sewing with a Janome HORIZON Memory Craft 9480 QC PROFESSIONAL Sewing Machine?
- M
  Mark SinghAug 25, 2025
  If you notice loops on the seams when using your Janome Sewing Machine, it could be because the needle thread tension is too loose, or the needle is either too thick or too fine for the fabric being used.
A
Anthony PetersAug 28, 2025
What to do if my Janome Sewing Machine does not run?
- P
  Peter TurnerAug 29, 2025
  If your Janome Sewing Machine isn't running, make sure it's plugged in. Also, check if thread is caught in the hook race, and verify that the start/stop button isn't being used while the foot control is plugged in.
M
Mark TaylorSep 1, 2025
Why does the needle thread keep breaking on my Janome HORIZON Memory Craft 9480 QC PROFESSIONAL Sewing Machine?
- S
  Shawn WallsSep 1, 2025
  If the needle thread breaks on your Janome Sewing Machine, it could be due to several reasons. Ensure the needle thread is threaded correctly and that the needle thread tension isn't too tight. Also, the needle may be bent or blunt, incorrectly inserted, or the thread may be tangled around the spool. Another thing to check is to make sure the needle thread is set under the presser foot when you start sewing and that the fabric isn't moved too fast when stitching free motion quilting. In any of these cases, changing the needle is recommended.
T
Timothy ValdezSep 5, 2025
Why doesn't the sewing speed increase on my Janome HORIZON Memory Craft 9480 QC PROFESSIONAL Sewing Machine with the A.S.R. foot holder?
- C
  Christopher RoseSep 5, 2025
  If the sewing speed doesn't increase and a buzzer sounds when using the A.S.R. foot holder on your Janome Sewing Machine, the speed control slider might be at the left side (low position). To fix this, move the speed control slider to the rightmost position for maximum sewing speed.
J
john63Sep 8, 2025
What to do if my Janome HORIZON Memory Craft 9480 QC PROFESSIONAL won't read the USB flash drive?
- G
  gmartinezSep 8, 2025
  If your Janome Sewing Machine isn't reading the USB flash drive, the format setting of the USB flash drive might not be correct, or the USB flash drive could be malfunctioning. To resolve this, replace the USB flash drive.

Janome HORIZON Memory Craft 9480 QC PROFESSIONAL Specifications

General

Maximum Stitch Width	9mm
Stitch Width	9mm
Maximum Stitch Length	5mm
Stitch Length	5mm
LCD Screen	Yes
LCD Touch Screen	Yes
Built-in Memory	Yes
Memory Function	Yes
Automatic Needle Threader	Yes
Built-in Needle Threader	Yes
Weight	26.5 lbs
AcuFeed Flex System	Yes
Automatic Thread Tension	Yes
Start/Stop Button	Yes
Needle Up/Down Setting	Yes
Thread Cutter	Yes
Automatic Thread Cutter	Yes
Knee Lifter	Yes
Speed Control	Yes
USB Port	Yes
Lighting	LED