Jebao DC Series User Manual

DC Pump
OWNER’S MANUAL
DCW-2000,DCW-3000,DCW-4000,DCW-5000,DCW-6500,DCW-8000,
DCW-10000
Introduction
The DC pumps are carefully inspected and tested to ensure both safety and operating
performance. However, failure to follow the instructions and warnings in this manual
may result in pump’s damage and/or serious injury. Be sure to read and save this
manual for future reference.
Pump Features
● SINE wave technology ,ultra quiet operation.
● High performance with innovational motor, and energy saving up to 65%, super
quiet operation.
● Suitable for both marine and fresh water, Rust free
● IC electronic detection ,automatic power-off protection upon no water.
● Motor protection if rotor is blocked; No copper element.
● With anti-resistant ceramic shaft, longer operation life.
Controller Features
● With 10 mode, adjustable the flow rate and head max.
● “Feed” Model, pause, timing, delay, restart function
● Memory function, ensure that the pump rework upon keeping the same parameter
Operating instructions
1. The pump must be connected with the controller and the 24V adaptor correctly
before work. According to the need to choose different plug and supply cord .
2. Turn on the power, press "-" and "+" button, to adjust the pump flow rate and
Head Max. and the LED instruction light will be on the relative mode
3. Lock / unlock function: press the "+" or "-" button for three seconds until the LED
light flash for two times, the controller locked; Similarly, press the "+" or "-" button for
three seconds again, LED indicator light flashes for two times, the controller unlocked
4. "FEED" function: when the pump is working, press "FEED" button, pump stops
working, the "10min" indicator lights up, the pump reworks automatically at previous
level after 10 minutes. Or you can press the “FEED” button to make the pump rework.
The LED flashing status instruction
No.
The controller
working status
LED flashing status
Elimination of
abnormal
phenomena
1
Over voltage or
under voltage
Check the input
supplying voltage
2
Controller
overheating
Check whether the
controller exposed
to the sunshine or
in high temperature
environment
3
The impeller stops
running
Check whether
something in the
pump or the parts
are wrongly
connected
4
Pump idling
Check the pump
work dry
5
Abnormal current of
the controller
Check if the pump
short of voltage or
the controller
broken
6
Lock or unlock
Press the "+" or "-" button for
three seconds until LED
indicator flashing for two
times, then the controller will
turn to be locked or unlocked
The key may be
broken if the light
don’t flash
Performance Parameters Table
No:
Model No:
Voltage
Control box (W)
Consumption
(W)
Flow rate
(L/H)
HeadMax(M)
1
DCW-2000
DC24V
DCW-2000
20
2000
2.5
2
DCW-3000
DC24V
DCW-3000
25
3000
3.0
3
DCW-4000
DC24V
DCW-4000
32
4000
4.0
4
DCW-5000
DC24V
DCW-5000
40
5500
4.0
5
DCW-6500
DC24V
DCW-6500
55
6500
4.5
6
DCW-8000
DC24V
DCW-8000
65
8000
5.5
7
DCW-10000
DC24V
DCW-10000
80
10000
6.0

Jebao DC Series Specifications

General

Model	DC Series
Adjustable Flow	Yes
Power Source	DC
Material	Plastic
Type	Submersible Pump
Controller	External Controller Included
Flow Rate	Varies by model
Max Head	Varies by model
Power Consumption	Varies by model
Connection Size	Varies by model
Weight	Varies by model

Summary

Introduction and Pump Features

Pump Features Details

Highlights SINE wave technology, high performance, energy saving, quiet operation, suitability for marine/fresh water, and automatic power-off.

Controller Features Details

Describes 10 modes, adjustable flow/head, feed model, pause, timing, delay, restart, and memory functions for parameter retention.

Operating and Safety Instructions

Operating Instructions

Steps for connecting pump, adjusting flow/head, and using lock/unlock and feed functions.

LED Flashing Status

Details LED indicators for controller working status, flashing patterns, and troubleshooting abnormal phenomena.

General Safety Warnings

Crucial safety advice including voltage limits, liquid types, water temperature, immersion, and supervision requirements.

Operation Cautions

Cautions on disconnecting power, avoiding dry running, lifting, heating liquid, and pool use, plus auto shut-off.

Pump Usage and Maintenance

Submersible Pump Usage

Guidance for submersible use, including complete submersion, water level, filter placement, and connection types.

Non-Submersible Pump Usage

Instructions for non-submersible use, positioning, hose connections, priming, and suction filters.

Maintenance and Troubleshooting

Steps for cleaning pump components, checking circuit, blockages, and rotor for non-operational issues.

Disposal Information