Jedia POWER 200A - Page 3

1
FEATURES
특󰼿󰼿󰼿󰼿󰼿󰼿징󰼿
HIGH EFFICIENT
"π"type air flux design makes high efficient cooling.
Air flux from right front and side to left front and side.
PROTECTION
PEAK CLIPPING LIMITER CIRCUIT
POWER "ON" DELAY CIRCUIT (SOFT START)
BUILT IN BRIDGED MONO FUNCTION
5-WAY BINDING POST AND SPEAKON CONNECTOR
Over heating protection
Input signal will be cut-off automatically when temperature of heat-
sink is more than 100 C.
Speaker protection
Designed amplifier bum sound to be minimized when power on/off.
Short protection
When input signal is supplied under the out of work for speaker,
short protection will be operating automatically.
Over current protection
Built in over current protection to protect output transistor.
"π"형󰼿공기󰼿흐름은󰼿기기󰼿내부의󰼿온도상승을󰼿억제하며,󰼿우수한󰼿방열󰼿
효과를󰼿나타냅니다.
우수한󰼿방열󰼿효과
방열판이󰼿100󰼿C를󰼿넘게되면󰼿자동적으로󰼿입력신호가󰼿끊기게󰼿됩니다.
과열󰼿방지회로
운용중󰼿스피커󰼿선로가󰼿쇼트되면󰼿쇼트󰼿보호회로가󰼿동작하여󰼿앰프가󰼿
고장나지󰼿않습니다.
스피커󰼿선로󰼿쇼트󰼿보호회로
과출력시에󰼿출력󰼿트랜지스터를󰼿보호하는󰼿회로가󰼿내장되어󰼿있습니다.
과전류󰼿보호회로󰼿
피크󰼿클리핑󰼿리미터󰼿회로
파워"ON"󰼿지연회로.(소프트󰼿스타트회로)
브릿지󰼿모노󰼿기능내장󰼿
5-WAY󰼿바인딩󰼿포스트󰼿및󰼿스피콘󰼿잭󰼿채택
파워󰼿스위치를󰼿켜거나󰼿끌때󰼿생기는󰼿붐󰼿잡음을󰼿최소화󰼿하도록󰼿설계되
어󰼿있습니다.
스피커󰼿보호회로
SAFETY INSTRUCTIONS
Read all safety instruction before operating the POWER A-Series amplifiers.
1. Install equipment as follow conditions.
The apparatus shall not be exposed to dripping or splashing and
no object filled with liquids, Such as vases, Shall be place on the
apparatus.
Install at the place, Not bending curved.
Do not install this apparatus in a confined space such as a book
case or similar unit.
Locate power amplifier away from heat source, Such as radiators
or other device that produce heat.
Do not drop objects or spill liquids into the inside of amplifier.
2. Keep in mind the following when connecting amplifier.
Connect the amplifier after reading of O/P manuals.
Connect each connection of amplifier perfectly, If not, It maybe
Caused hum, Damage, Electric shock in case of mis-connecting.
To prevent electric shock, Do not open top cover.
Connect the power cord with safety after check of AC power.
안󰼿전󰼿사󰼿항
제품을󰼿운용하기전에󰼿모든󰼿안전사항을󰼿읽어󰼿보십시오.󰼿
1.󰼿이런󰼿장소에󰼿설치하여󰼿주십시오.
진동이나󰼿경사가󰼿심하지󰼿않고󰼿바닥이󰼿평평한󰼿장소.
통풍이󰼿잘되고󰼿물기나󰼿습기가󰼿많지󰼿않은󰼿장소.
직사광선을󰼿받지󰼿않는󰼿장소󰼿또는󰼿난방기구(발열체)에서󰼿멀리󰼿떨어진󰼿장소.󰼿
인화성󰼿물질(화학약품)이󰼿없는󰼿장소.
2.󰼿설치시󰼿이런점을󰼿주의하십시오.
사용설명서󰼿시스템󰼿연결방법을󰼿완전히󰼿읽으신󰼿후에󰼿연결해󰼿주십시오.
각종󰼿연결선을󰼿완전하게󰼿연결해󰼿주십시오.
(주전원󰼿코드를󰼿뽑은󰼿상태에서󰼿연결.)
불완전한󰼿연결은󰼿잡음,󰼿제품의󰼿손상󰼿또는󰼿안전사고의󰼿원인이󰼿됩니다.
전기적󰼿충격󰼿또는󰼿감전사고의󰼿위험이󰼿있으므로󰼿뚜껑을󰼿열지󰼿말아주십시오.󰼿
주󰼿교류󰼿전원󰼿플러그를󰼿연결하기󰼿전에󰼿사용전압을󰼿확인하신󰼿후󰼿안전하게󰼿
연결하십시오.
제품을󰼿수리시는󰼿규정된󰼿부품과󰼿자격이󰼿있는󰼿사람이󰼿수리를󰼿하여야󰼿함.
Amplifiers should be serviced by qualified service person.