When the vehicle has reached the desired speed, push
the SET (+) or SET (-) button and release. Release the
accelerator and the vehicle will operate at the selected
speed.
To Vary The Speed Setting
To Increase Or Decrease The Set Speed
When the Cruise Control is set, you can increase speed
by pushing the SET (+) button, or decrease speed by
pushing the SET (-) button.
U.S. Speed (mph)
•
Pushing the SET (+),orSET(-) button once will
result ina1mphspeed adjustment. Each subse-
quent tap of the button results in an adjustment of
1 mph.
•
If the button is continually pushed, the set speed
will continue to adjust in 5 mph increments until the
button is released, then the new set speed will be
established.
Metric Speed (km/h)
•
Pushing the SET (+),orSET(-) button once will
result ina1km/hspeed adjustment. Each subse-
quent tap of the button results in an adjustment of
1 km/h.
•
If the button is continually pushed, the set speed
will continue to adjust in 10 km/h increments until
the button is released, then the new set speed will
be established.
To Accelerate For Passing
While the Cruise Control is set, press the accelerator to
pass as you would normally. When the pedal is
released, the vehicle will return to the set speed.
USING CRUISE CONTROL ON HILLS
The transmission may downshift on hills to maintain the
vehicle set speed.
The Cruise Control system maintains speed up and
down hills. A slight speed change on moderate hills is
normal. On steep hills, a greater speed loss or gain may
occur so it may be preferable to drive without Cruise
Control.
WARNING!
Cruise Control can be dangerous where the system
cannot maintain a constant speed. Your vehicle could
go too fast for the conditions, and you could lose con-
trol and have an accident. Do not use Cruise Control
in heavy traffic or on roads that are winding, icy,
snow-covered or slippery.
To Resume Speed
To resume a previously set speed, push the RES button
and release. Resume can be used at any speed above
20 mph (32 km/h).
To Deactivate
A soft tap on the brake pedal, pushing the CANC (can-
cel) button, or normal brake pressure while slowing the
vehicle will deactivate the Cruise Control without eras-
ing the set speed from memory.
The following conditions will also deactivate the Cruise
Control without erasing the set speed from memory:
•
Vehicle parking brake is applied
•
Stability event occurs
•
Gear selector is moved out of DRIVE
•
Engine overspeed occurs
•
Clutch pedal is pressed (manual transmission only)
•
Vehicle is operating at a low RPM (manual transmis-
sion only)
Pushing the on/off button or placing the ignition in the
OFF position, erases the set speed from memory.
ADAPTIVE CRUISE CONTROL (ACC)
Adaptive Cruise Control (ACC) increases the driving con-
venience provided by Cruise Control while traveling on
highways and major roadways. However, it is not a
safety system and not designed to prevent collisions.
The Cruise Control function performs differently if your
vehicle is not equipped with ACC
page 146.
ACC will allow you to keep Cruise Control engaged in
light to moderate traffic conditions without the constant
need to reset your speed. ACC utilizes a radar sensor
and a forward facing camera designed to detect a
vehicle directly ahead of you to maintain a set speed.
NOTE:
•
If the ACC sensor detects a vehicle ahead, ACC will
apply limited braking or accelerate (not to exceed
the original set speed) automatically to maintain a
preset following distance, while matching the speed
of the vehicle ahead.
•
Any chassis/suspension or tire size modifications to
the vehicle will affect the performance of the Adap-
tive Cruise Control and Forward Collision Warning
system.
•
Fixed Speed Cruise Control (ACC not enabled) will
not detect vehicles directly ahead of you. Always be
aware of the feature selected
page 366.
STARTING AND OPERATING 147
4
To Next Page
Loading...
