Jensen Phase Linear UV10 User Manual (English)

Other manuals for Jensen Phase Linear UV10

Questions and Answers:

E
Elizabeth WongAug 20, 2025
Why is there no audio output from my Jensen Car Receiver?
- W
  warrenmariaAug 20, 2025
  If you are experiencing no or low audio output on your Jensen Car Receiver, there are several potential causes. First, check the wiring to ensure proper audio output connection and correct any issues. Make sure the volume isn't set too low and increase it if necessary. Review the wiring diagram to check the 'MUTE' connection. If the speakers are damaged, consider replacing them. Also, adjust the channel balance to the center position if it's heavily biased. Finally, ensure speaker wiring isn't in contact with any metal parts of the car, and if it is, insulate the connections.
M
Michael ConradAug 22, 2025
How to fix a Jensen Car Receiver that will not power on?
- N
  Nancy Le MDAug 22, 2025
  If your Jensen Car Receiver won't power on, the radio fuse or car battery fuse may be blown. Replace the blown fuse with a new one of the correct rating. Alternatively, the unit may be in an illegal operation state. In this case, press the RESET button located in the bottom right corner of the front panel.
A
Antonio WilliamsAug 25, 2025
Why is the sound quality poor on my Jensen Car Receiver?
- C
  Corey ReevesAug 25, 2025
  If you're experiencing poor sound quality or distortion with your Jensen Car Receiver, the issue could be due to several factors. If you are using a pirated disc, use an original copy instead. Ensure that the speaker power rating is compatible with the unit; if not, connect proper speakers. Also, check the speaker contact to make sure the speaker is not shorted.
P
Patty JacksonAug 26, 2025
What to do if the Jensen Phase Linear UV10 remote control does not function?
- L
  Laura PerezAug 26, 2025
  If the remote control for your Jensen Car Receiver isn't working, the battery may be depleted. Replace it with a new one. Alternatively, the battery might be installed incorrectly; remove it and reinstall it correctly.
E
Eric McmahonAug 28, 2025
Why is my Jensen Phase Linear UV10 Car Receiver having weak station searching?
- B
  Brianna ThompsonAug 28, 2025
  If your Jensen Car Receiver is having trouble finding stations, it could be due to the auto antenna not being fully extended or properly connected. Ensure the auto antenna control cable is correctly connected. Also, check if the LOCAL function is activated and turn it off if it is.
M
Melissa ParsonsAug 29, 2025
Why is there no image on my Jensen Car Receiver screen?
- A
  Amber PattersonAug 29, 2025
  If there is no image on your Jensen Car Receiver, check the connection to the parking brake wire and correct it if necessary. Also, ensure the parking brake is engaged by stopping the vehicle in a safe place and applying it.
K
Kevin ButlerAug 31, 2025
What to do if my Jensen Phase Linear UV10 disc does not play back?
- A
  Ashley SimmonsAug 31, 2025
  If your Jensen Car Receiver isn't playing discs, it could be due to several reasons. The disc may be warped or scratched, so use a disc in good condition. If the disc is dirty or wet, clean it with a soft cloth. The laser pickup might be dirty, so clean it with a cleaning disc. Ensure you are using a compatible disc and that the disc rating does not exceed the Parental Lock rating limit; if it does, change the Parental Lock settings to lower the restriction. Also, check that the disc region code is compatible with the unit and that the disc is inserted with the label side up.
J
Jennifer WhiteSep 2, 2025
Why is my Jensen Car Receiver screen flashing?
- D
  Danny LeeSep 2, 2025
  If you're seeing a flashing image or interference on the screen of your Jensen Car Receiver, it could be because the DVD is not compatible with the current TV system settings. Change the setup to accommodate the disc. Alternatively, there may be improper video signal connections; check the wiring and correct it if necessary.
M
Maria PattersonSep 4, 2025
Why does my Jensen Phase Linear UV10 reset when the engine is off?
- J
  jrogersSep 4, 2025
  If your Jensen Car Receiver resets itself when the engine is off, there may be an incorrect connection between the ACC and the positive battery wire. Check the wiring and correct it.
S
Steven PowersSep 6, 2025
Why is the image on my Jensen Phase Linear UV10 blurred?
- J
  Joy HaasSep 6, 2025
  If the image on your Jensen Car Receiver is blurred, distorted, or dark, it could be because the disc is illegally copied. Use an original disc instead.

Jensen Phase Linear UV10 Specifications

General

Number of Channels	4
Detachable Face	No
AUX Input	Yes
Built-in Bluetooth	Yes
USB Port	Yes
AM/FM Tuner	Yes
Remote Control	Yes
Compatible with Steering Wheel Controls	Yes
Display Type	LCD