Why is the filling so short in my Jet-tech Washer?
If the filling process of your Jet-tech Washer is too short, the air trap may have dirt in it, so clean the air trap. Also, the air pressure switch may be faulty; adjust or replace as required.
What to do if my Jet-tech Dishwasher overflows?
If your warewasher is overflowing, the drain outlet hose may be kinked or blocked; straighten or unblock it. Also, the drain pump might be blocked or defective; call for service to address this issue, keeping in mind that blockages due to food or debris are not covered under warranty. High incoming water pressure could also be the cause; if it's above 3 BAR, a Pressure Reducing Valve must be installed. Excessive suds from non-commercial detergent can also cause overflow. If this happens, turn off the washer, drain the wash tank, remove as much suds as possible, and run the unit without the overflow pipe for 2-4 minutes before refilling.
Why is the wash pump not working consistently in my Jet-tech Washer?
If the wash pump in your Jet-tech Washer isn't operating consistently during a wash cycle, the air trap may have dirt in it, so clean the air trap. Also, the air pressure switch may be faulty; adjust or replace it as required. Ensure the machine is leveled. If the water level in the wash tank is too low, adjust the pressure switch or replace it as required.
Why is the filling taking too long in my Jet-tech Washer?
If the filling process of your Jet-tech Washer is taking too long, the air trap may have dirt in it, so clean the air trap. Also, the air pressure switch may be faulty; adjust or replace it as required.
How to prevent spotting on glassware in my Jet-tech Washer?
If you're noticing spotting on glassware after washing in your Jet-tech Washer, the rinse agent may be of an inferior quality; replace it with a quality commercial brand. Additionally, the rinse aid pump may need to be primed or adjusted; prime or adjust, replacing as required.
Why are the pilot lamps not working on my Jet-tech Washer?
If the pilot lamps on your Jet-tech Washer aren't illuminating, start by checking the power switch to ensure it's properly connected and not defective; replace if necessary. Verify that power is reaching the machine by checking the breaker and electrical connections. The door micro switch may be misaligned, so adjust or replace it as needed. Other potential issues include a defective timer, momentary relay, or wash cycle button; replace these components if necessary. Also, check the pilot lamp connections and replace the lamps if faulty. Finally, verify the thermostats, as both may be defective.
Why does my Jet-tech Washer take so long to empty?
If your Jet-tech Washer is taking too long to empty, the drain outlet hose may be blocked, or the drain pump may be blocked or defective, preventing proper drainage. Un-clog or reposition the hose, and un-clog or replace the drain pump as needed. Additionally, the overflow pipe may be clogged; clean out any residue.
How to fix Jet-tech Washer overflow?
If your Jet-tech Washer is overflowing, the solenoid valve may have dirt in it or may be defective, so replacement may be required. Incorrect incoming water pressure can also cause this issue. Check the drain outlet hose for blockages, and ensure the drain pump isn't blocked or defective, preventing proper drainage. Un-clog or reposition the hose and un-clog or replace the drain pump as needed. Lastly, the overflow itself may be clogged; clean out any residue.
What to do if my Jet-tech Washer does not start?
If your Jet-tech Washer isn't starting, begin by checking the power switch to ensure it's properly connected and not defective; replace if necessary. Verify that there's power reaching the machine by checking the breaker and electrical connections. A defective door micro switch, timer, momentary relay, or washing cycle button could also be the issue; consider adjusting or replacing these parts. Look for short circuits in the electrical components or wiring, and check all connections. Also, the solenoid valve may have dirt on it or may be defective; clean filter or replace as required. Additionally, a faulty pressure switch can prevent the washer from starting; adjust or replace it.
What to do if drain time exceeds 2 minutes on my Jet-tech F-22?
If the drain time exceeds 2 minutes, the drain hose may be kinked, or the drain is blocked. The drain pump may also be blocked and/or defective. Unclog or reposition the hose, and/or replace the drain hose. Unclog or replace the drain pump, as required. If problems persist, call for service.
Covers warranty period, conditions, and limitations for Jet Tech warewashers.
Guides users through the initial power-on, water fill, and heating processes.
Explains the electrical flow from power-on through heating to the ready state.
Details the electrical components and sequence for wash and rinse cycles.
Provides instructions on identifying and adjusting wash and booster thermostats for correct temperatures.
Explains the role of the air pressure switch in water level regulation.
Details the procedure for adjusting the air pressure switch to set water levels.
Guides on adjusting the amount of rinse additive dispensed by the pump.
Explains how to adjust the rate at which the liquid detergent pump dispenses.
Describes the function of the drain pump and models equipped with it.
Explains how to adjust the timing and duration of detergent injection pulses.
Instructions for replacing the water inlet valve, including specific notes for certain models.
Addresses problems related to dirty dishes, poor rinsing, and foreign material.
Covers issues preventing the machine from starting or operating correctly.
General| Brand | Jet-tech |
|---|---|
| Model | F-22 |
| Category | Dishwasher |
| Language | English |
To Next Page
