Jet AP-0 - User Manual

3
GB - ENGLISH
Operating Instructions
Dear Customer,
Many thanks for the confidence you have shown in us with the purchase of your new JET-machine. This manual has been
prepared for the owner and operators of a JET AP-0, AP-1, AP-2 AP-3, AP-5 arbor press to promote safety during
installation, operation and maintenance procedures. Read this manual thoroughly and follow instructions carefully.
…Table of Contents
1. Declaration of conformity
2. Warranty
3. Safety
Authorized use
Safety notes
4. Machine specifications
Technical data
Machine description
5. Transport and Installation
Transport
Installation
Initial Lubrication
6. Machine operation
7. Adjustments
8. Maintenance
9. Environmental protection
1. Declaration of conformity
On our own responsibility we
hereby declare that this product
complies with the regulations*
listed on page 2. Designed in
consideration with the standards**.
2. Warranty
The Seller guarantees that the
supplied product is free from
material defects and
manufacturing faults. This
warranty does not cover any
defects which are caused, either
directly or indirectly, by incorrect
use, carelessness, accidental
damage, repair, inadequate
maintenance or cleaning and
normal wear and tear. Guarantee
and/or warranty claims must be
made within twelve months from
the date of purchase (date of
invoice). Any further claims shall
be excluded. This warranty
includes all guarantee obligations
of the Seller and replaces all
previous declarations and
agreements concerning warranties.
The warranty period is valid for
eight hours of daily use. If this is
exceeded, the warranty period
shall be reduced in proportion to
the excess use, but to no less than
three months.
Returning rejected goods requires
the prior express consent of the
Seller and is at the Buyer’s risk
and expense.
Further warranty details can be
found in the General Terms and
Conditions (GTC). The GTC can
be viewed at www.jettools.com or
can be sent by post upon request.
The Seller reserves the right to
make changes to the product and
accessories at any time.
3. Safety
3.1 Authorized use
The arbor press is designed for
pressing, broaching, bending and
straightening purposes only.
The proper use also includes
compliance with the operating and
maintenance instructions given in
this manual.
For machining, the workpiece must
allow to safely be loaded and
supported.
The machine must be operated
only by persons familiar with its
operation and maintenance and
who are familiar with its hazards.
The required minimum age must
be observed.
The machine must only be used in
a technically perfect condition.
When working on the machine, all
safety mechanisms and covers
must be mounted.
Any other use exceeds
authorization.
In the event of unauthorized use of
the machine, the manufacturer
renounces all liability and the
responsibility is transferred
exclusively to the operator.
3.2 Safety notes
Metal forming machines can be
dangerous if not used properly.
Read and understand the entire
instruction manual before
attempting assembly or operation.
Keep this operating instruction
close by the machine, protected
from dirt and humidity, and pass it
over to the new owner if you part
with the tool.
Install the machine so that there is
sufficient space for safe operation
and work piece handling.
Keep work area well lighted.

Summary

Declaration of Conformity

Warranty Information

Safety Guidelines

Authorized Use

Defines the arbor press's intended use for pressing, broaching, bending, and straightening.

General Safety Notes

Emphasizes reading the manual, keeping instructions accessible, and ensuring safe operating space.

Machine Specifications

Technical Data

Provides detailed specifications for AP-0, AP-1, AP-2, AP-3, and AP-5 models, including dimensions and pressure.

Machine Description

Describes the components and purpose of the arbor press, referencing Figure 1 for visual identification.

Transport and Installation

Transport Procedures

Instructions for safely transporting the machine using forklifts or hand trolleys, and handling transport damage.

Installation Requirements

Details on how to properly install the arbor press in a closed room, bolting it to a workbench or table.

Initial Lubrication Steps

Refers to chapter 8 for specific instructions on initial lubrication of the machine.

Machine Operation

Adjustments and Maintenance

Adjustment Guidance

Instructions for tightening bolts if the ram becomes loose or falls by itself, ensuring equal tension.

Maintenance Procedures

Covers daily lubrication, oiling the pinion, greasing the ram rack, and oiling machined parts.

Environmental Protection

Jet AP-0 Specifications

General

Brand	Jet
Model	AP-0
Category	Power Tool
Language	English