EasyManua.ls Logo

Jet JWS-10 - User Manual

Jet JWS-10
36 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
JET
427 New Sanford Road
LaVergne, Tennessee 37086 Document No. M-727100
Ph.: 800-274-6848 Edition 1 05/2020
www.jettools.com Copyright © 2020 JET
Operating Instructions and Parts Manual
10” Slow Speed Wet Sharpener
Model JWS-10

Table of Contents

Questions and Answers

  • S
    Stephanie SnowAug 15, 2025
    What to do if my Jet JWS-10 motor won't start and the fuses keep blowing?
    • H
      Heather LopezAug 15, 2025
      If the Jet Power Tool motor won't start and fuses blow or circuit breakers trip, it might be due to several reasons. First, too many electrical machines might be running on the same circuit, so turn off other machines and try again. An incorrect fuse could also be the problem, so use a time-delay fuse, or switch to a circuit with a higher rated fuse or breaker. Check for obstructions preventing wheel rotation, and if found, unplug the tool and clear the wheels. An undersized extension cord can cause this issue, so ensure you're using the correct size. Finally, inspect the cord or plug for damaged insulation and shorted wires, and check all motor connections for looseness, shorts, or worn insulation.
  • C
    Christopher JohnsonAug 18, 2025
    How to troubleshoot a Jet JWS-10 Power Tool when the motor will not start?
    • M
      Melanie DavisAug 18, 2025
      If your Jet Power Tool motor won't start, begin by verifying that the plug is properly inserted into the receptacle. If that's not the issue, check the motor cord for cuts or abrasions and replace it if damaged. Also, reset any blown fuses or tripped circuit breakers, keeping in mind that too many machines on one line can cause this. Replace a faulty plug with a new one. Low line voltage can also prevent the motor from starting, so check the power line for proper voltage. Inspect all lead connections on the motor for loose or open connections. If the switch is faulty, replace it. If none of these steps work, it could be a motor failure, and you should contact JET technical service.
  • N
    Nathan DuarteAug 21, 2025
    Why does my Jet JWS-10 Power Tool motor slow down or lack full power?
    • R
      Rachel EdwardsAug 22, 2025
      If the Jet Power Tool motor slows down or doesn't develop full power, it could be due to low line voltage, so check the power line for proper voltage. Another cause might be an overloaded motor; reduce the load and avoid pressing too hard. If the problem persists, it could indicate a motor failure, and you should contact JET technical service.
  • P
    plewisAug 25, 2025
    What causes a Jet Power Tool motor to stall and blow fuses?
    • S
      Susan GarciaAug 26, 2025
      If the Jet Power Tool motor stalls, causing blown fuses or tripped circuits, the motor may be overloaded, so reduce the load and avoid pressing too hard. Check the motor connections for loose or shorted terminals, or worn insulation. Low voltage can also cause this issue, so correct any low voltage conditions. Ensure the correct fuses or circuit breakers are installed in the power line. Also, inspect all connections for looseness.
  • C
    crystal95Aug 28, 2025
    Why is my Jet JWS-10 Power Tool experiencing excessive vibration?
    • K
      Kathleen ArmstrongAug 28, 2025
      Excessive vibration in your Jet Power Tool can be caused by several factors. Ensure the machine is placed on a flat surface. If the stone wheel is out of balance, dress it. If one side of the wheel is saturated, allow it to dry and avoid leaving an idle wheel immersed in water. Also, check all fasteners to ensure they are secure.
  • J
    Joseph RoachAug 31, 2025
    Why doesn’t the wheel on my Jet JWS-10 hold an edge?
    • S
      Stephanie NelsonAug 31, 2025
      If the wheel on your Jet Power Tool doesn’t hold an edge or wears too rapidly, it might be due to applying too much pressure; use lighter pressure and let the wheel do the work. It could also be due to a poor grade of wheel, so use quality wheels.
  • S
    Samuel DeckerSep 4, 2025
    What causes marring of tool edge on my Jet JWS-10 Power Tool?
    • M
      Mikayla ChanSep 4, 2025
      Marring of a tool edge on your Jet Power Tool can occur due to debris on the wheel. Dress the wheel for a fresh surface and clean debris from the tank, refilling it with fresh water.
  • J
    Justin NelsonSep 7, 2025
    What to do if the wheel slips during rotation on my Jet JWS-10 Power Tool?
    • O
      ortegachristineSep 7, 2025
      If the wheel slips during rotation on your Jet Power Tool, it could be due to insufficient torque adjustment. Use the torque adjust knob to remedy this. Also, ensure that the screw or knob is tightened down properly, but avoid overtightening.
  • D
    Debbie BryantSep 10, 2025
    Why does grinding create an angle on my Jet Power Tool?
    • K
      Kristin PierceSep 12, 2025
      If grinding creates a slight angle along the width of the tool on your Jet Power Tool, it could be because the jig is slipping; make sure the jig is tightened down. Another possibility is that the support arm is not parallel to the wheel; adjust the support arm to make it parallel.

Summary

IMPORTANT SAFETY INSTRUCTIONS

Specifications

Setup and assembly

Installation Steps

Covers mounting the stone wheel, installing the water tank, and optional support arm.

Electrical connections

Grounding instructions

Explains the importance and procedure for properly grounding the equipment.

Extension cords

Adjustments

Sharpening jig set up

Steps for configuring the sharpening jig to set the correct cutting edge angle.

Basic operation

Stone wheel dressing

Tool grinding

Proper technique for grinding tools using jigs and fixtures for safety.

Tool honing

User Maintenance

Wheel replacement

Troubleshooting JWS-10 Wet Sharpener

Motor and electrical problems

Diagnosing and correcting issues related to the motor and electrical system.

Mechanical and operational problems

Addressing common mechanical and operational issues encountered during use.

Jet JWS-10 Specifications

General IconGeneral
Motor Power1 HP
Table Size7-1/4 x 30 in.
Weight42 lbs
SwitchOn/Off
Dust ExtractionYes

Related product manuals