Johnson Controls HMH7 Series User Manual (English)

Other manuals for Johnson Controls HMH7 Series

Questions and Answers:

C
Casey VillegasAug 16, 2025
Why does my Johnson Controls Heat Pump keep turning off due to high-pressure protection?
- W
  wellsandrewAug 16, 2025
  If your Johnson Controls Heat Pump is turning off due to high-pressure protection, it could be due to several reasons. Here's what to check: * Ensure the wiring of the high-pressure switch has a secure connection. Reconnect if necessary. * The high-pressure switch itself may have failed and need replacement. * The outdoor control board may be abnormal, requiring replacement.
B
batesemilyAug 19, 2025
What causes a Johnson Controls HMH7 Heat Pump unit overcurrent turn-off fault?
- T
  Tammy JonesAug 19, 2025
  A unit overcurrent turn-off fault in your Johnson Controls Heat Pump can be caused by several factors: * A failure in the control board current sampling circuit, which would require replacing the electrical control board components. * Excessive current due to low supply voltage, resulting in normal protection activation. * Compressor failure, necessitating compressor replacement.
J
joshuatorresAug 22, 2025
What causes low-pressure switch protection in a Johnson Controls Heat Pump?
- N
  Nicholas JordanAug 22, 2025
  If your Johnson Controls Heat Pump is experiencing low-pressure switch protection, consider these potential causes: * A poor connection in the wiring of the low-pressure switch. Reconnect the wiring. * Failure of the low-pressure switch itself, requiring replacement. * A low refrigerant charge. Check for refrigerant leaks and adjust the charge. * Failure of the expansion valve in heating mode. Replace the expansion valve. * An abnormal outdoor control board. Replace the outdoor control board.
Y
yrobertsAug 26, 2025
How do I troubleshoot an EEprom data error in my Johnson Controls HMH7 Heat Pump?
- C
  Christine YangAug 26, 2025
  If you're encountering an EEprom data error with your Johnson Controls Heat Pump, it could be due to: * Failure of the EE components, which would require replacing the board. * Failure of the EE components control circuit, necessitating replacement of the outdoor control board components. * Incorrectly inserted EE components. Try resetting them.
S
Stacey LewisAug 28, 2025
What to do if I have an outdoor ambient temperature sensor fault on my Johnson Controls Heat Pump?
- E
  Emily RobertsAug 28, 2025
  If you're experiencing an outdoor ambient temperature sensor fault with your Johnson Controls Heat Pump, you can try the following: * Check for a poor connection and reconnect the outdoor ambient temperature sensor. * If the sensor has failed, replace the outdoor ambient temperature sensor components. * If the sampling circuit has failed, replace the outdoor control board components.
B
Brandon SantiagoAug 31, 2025
What does it mean when my Johnson Controls HMH7 Heat Pump shows an outdoor coil temperature sensor fault?
- J
  Julie MorrisAug 31, 2025
  An outdoor coil temperature sensor fault on your Johnson Controls Heat Pump could indicate: * A poor connection with the outdoor coil temperature sensor. Reconnect the sensor. * A failed outdoor coil temperature sensor. Replace the sensor components. * A sensor circuit failure. Replace the outdoor control board components.
W
Wendy DavisSep 3, 2025
What to do if my Johnson Controls HMH7 is not communicating between the indoor and outdoor units?
- C
  Christopher Phelps MDSep 3, 2025
  If you are experiencing a communication fault between the indoor and outdoor units of your Johnson Controls Heat Pump, here are some things you can check: * Ensure the low-voltage cable is correctly connected according to the wiring diagram. Reconnect if necessary. * Check for and reconnect any loose low-voltage connections. * If the low-voltage cable is damaged, replace it. * The outdoor control board may have failed and require replacement. * Inspect the low-voltage circuit and adjust the DIP switch and short-circuit fuse. * Ensure you are using a suitable low-voltage cable, referring to the installation instructions.