EasyManua.ls Logo

Jonsered FR 2216 MA User Manual

Jonsered FR 2216 MA
32 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
FR 2213 MA FR 2216 MA FR 2216 MA 4X4
Oper
ator
s manual
Please read the oper
ator’s manual carefully and
make sure you understand the instructions
before using the machine.

Table of Contents

Questions and Answers:

Jonsered FR 2216 MA Specifications

General IconGeneral
BrandJonsered
ModelFR 2216 MA
CategoryLawn Mower
LanguageEnglish

Summary

KEY TO SYMBOLS

Symbols

Lists and explains various symbols found on the machine and in the instructions for safe operation and identification.

Starting instructions

Provides step-by-step guidance on how to safely start the engine of the machine.

INTRODUCTION

Dear Customer,

Welcomes the customer and highlights the value of the operator's manual for machine longevity and resale value.

Driving and transport on public roads

Advises on checking road regulations and securing the machine properly for transport on public roads or other vehicles.

Towing

Explains the precautions and risks associated with towing the machine, especially regarding transmission damage.

Use

Defines the intended use of the ride-on mower and emphasizes compliance with manufacturer recommendations for operation and repair.

Good service

Stresses the importance of genuine parts, dealer inspection, and a documented service history for optimal support and resale value.

Service journal

Pre-delivery service

Lists essential checks and tasks to be performed before the machine is delivered to the customer for safe operation.

After the first 8 hours

Outlines the initial maintenance checks and actions required after the first 8 hours of machine operation.

WHAT IS WHAT?

Location of the controls

Identifies and explains the function of each control and component on the machine's operating panel.

SAFETY INSTRUCTIONS

Safety instructions

Provides general safety guidelines and warnings to prevent injury and ensure safe operation of the machine.

General use

Details essential safety practices for operating the machine, including understanding controls, user age, and clearing the work area.

Driving on slopes

Offers critical advice and precautions for safely operating the machine on sloped terrain to prevent accidents and overturning.

Children

Warns about the dangers posed by children around the machine and provides instructions for ensuring their safety.

Maintenance

Outlines crucial safety precautions to be taken before and during maintenance procedures to prevent injury and damage.

Transport

Provides essential safety information and instructions for properly securing the machine during transport to prevent accidents and damage.

PRESENTATION

Presentation

Congratulates the customer and introduces the machine's features and design, referencing the operator's manual.

Parking brake

Explains the procedure for applying and releasing the parking brake to secure the machine when stopped.

Speed limiter

Describes how the speed of the machine is regulated using two pedals for forward and backward movement.

Throttle and choke controls

Details the function of the throttle control for engine speed and the choke for cold starting.

Cutting unit

Describes the Combi-unit, its mulching function, and its operation as a rear ejection unit.

Lifting lever for the cutting unit

Explains how to use the lifting lever to move the cutting unit between transport and mowing positions.

Cutting height adjustment lever

Explains how to adjust the cutting height of the unit through multiple positions using a lever.

Seat

Describes the seat's attachment and adjustment features for operator comfort and positioning.

Fueling

Provides instructions on safely fueling the machine with the correct type of unleaded petrol and precautions.

Release lever FR 2213 MA, FR 2216 MA

Explains how to use the release lever to move the machine when the engine is shut off.

Release lever FR 2216MA 4X4

Details the operation of the release levers for the front and rear axles on the 4x4 model for disengaging drive.

Driving

Before starting

Lists essential checks and preparations required before starting the engine and operating the machine.

Start the engine

Provides a step-by-step guide on how to safely start the engine, including cold and warm start procedures.

Starting the engine with a weak battery

Explains how to safely jump-start the machine using another vehicle's battery, with important warnings.

Driving the Rider

Details how to release the parking brake, control speed with pedals, and select cutting height for operation.

Stop the engine

Outlines the correct procedure for safely stopping the engine and securing the machine after use.

Maintenance

Maintenance schedule

Presents a comprehensive schedule of daily, annual, and interval-based maintenance tasks for the machine.

Cleaning

Provides instructions and recommendations for cleaning the machine after use to prevent rust and maintain performance.

Removing of the machine hoods

Explains how to remove the engine cover, front cover, and side fenders for access to internal components.

Muffler

Advises on checking the muffler's condition and security, with warnings about its high operating temperature.

Checking and adjusting the steering wires

Describes how to check and adjust the tension of the steering wires to ensure proper steering alignment.

Adjusting the parking brake

Details the procedure for adjusting the parking brake to ensure it holds the machine securely on slopes.

Adjusting the throttle wire

Explains how to adjust the throttle cable for optimal engine response and performance.

Replacing the air filter

Provides step-by-step instructions for replacing the air filter to maintain engine power and smooth running.

Replacement of fuel filter

Guides on how to replace the fuel filter at recommended intervals to ensure proper fuel delivery to the engine.

Checking the fuel pump's air filter

Advises on checking and cleaning the fuel pump's air filter for optimal fuel system performance.

Checking the tyre pressure

Specifies the correct tyre pressure for all wheels and mentions adjusting rear tyre pressure for improved drive.

Ignition system

Focuses on the maintenance of the spark plug, including replacement and gap adjustment for engine ignition.

Fuses

Identifies the location and type of the main fuse and explains how to replace a blown fuse to protect the electrical system.

Check the safety system

Explains how to check the machine's safety interlock systems to ensure they function correctly before starting or operating.

Checking the engine's cooling air intake

Details how to clean the engine's air intake grille and duct to ensure adequate cooling and prevent engine damage.

Checking and adjustment of the cutting unit's ground pressure

Guides on checking tyre pressure and adjusting the cutting unit's ground pressure for optimal cutting results.

Checking the cutting unit's parallelism

Explains how to check the cutting unit's parallelism to ensure a level cut and proper blade alignment.

Adjusting the parallelism of the cutting unit

Provides instructions for adjusting the cutting unit's parallelism for optimal cutting performance.

Service position for the cutting unit

Details the procedure for placing the cutting unit in a service position for easy access during cleaning, repairs, and servicing.

Checking the blades

Emphasizes the importance of checking blades for damage and sharpness for optimal mowing results and safety.

Replacing the blades

Provides step-by-step instructions for safely removing and replacing the cutting blades, including torque specifications.

Removing the Mulching plug

Explains how to remove the mulching plug to change the Combi unit from mulching to rear ejection mode.

Lubrication

Checking the engine's oil level.

Instructs on how to check the engine oil level when the machine is horizontal and the engine is off.

Replacing the engine oil

Details the procedure for changing the engine oil, including frequency, draining, and refilling with correct oil type.

Changing the oil filter

Provides instructions for replacing the oil filter at recommended intervals for engine protection.

Checking the transmission oil level

Explains how to check the transmission oil level and identifies the correct oil types for different models.

Lubricating the belt adjuster

Details the procedure for lubricating the belt adjuster using specific grease for proper function.

General lubrication

Covers general lubrication points for joints, bearings, and control wires using specified greases and oils.

Troubleshooting schedule

Storage

Winter storage

Provides detailed instructions on preparing the machine for long-term storage, including fuel treatment, cleaning, and battery care.

Guard

Mentions a cover for protection during storage or transport and advises contacting the dealer for a demonstration.

Service

Recommends performing service during the low season and emphasizes using genuine parts and annual check-ups by an authorized dealer.

TECHNICAL DATA

EC Declaration of Conformity (Applies to Europe only)

Declares the machine's compliance with relevant European directives and harmonised standards.

Related product manuals