Need help?Do you have a question about the Jonsered FR 2215 MA 4X4 and is the answer not in the manual?
General| Engine Manufacturer | Briggs & Stratton |
|---|---|
| Engine Name | Intek |
| Cylinders | 1 |
| Transmission Type | Hydrostatic |
| Drive Method | Pedal-operated |
| Engine Type | 4-stroke |
| Cutting Height Adjustment | Central |
| Engine Displacement | 500 cm³ |
| Drive System | AWD |
Instructions for safe driving and transporting the machine on roads and other vehicles.
Guidelines for towing the machine, including precautions to prevent transmission damage.
Details on the intended use of the ride-on mower and important operational information.
Information on customer support, dealer service, and the importance of service history.
Checklist and procedures for initial service before customer delivery.
Specific maintenance tasks recommended after the first 8 hours of operation.
Explanation of common symbols found on the machine and in the manual.
Symbols and instructions related to starting the engine, controls, and maintenance checks.
Essential safety rules for operating the machine, including warnings and personal protection.
Guidance on insuring the rider and understanding liability for accidents.
Critical safety guidelines for operating the machine on sloped terrain.
Precautions to ensure the safety of children around the machine during operation and maintenance.
Safety rules to follow when performing maintenance tasks on the machine.
Safety measures and procedures for transporting the machine on a vehicle or trailer.
Identification and numbering of all controls on the machine.
Introduction to the Jonsered Frontrider and its features.
Details about the cutting unit, including rear ejection and Combi-unit.
Explanation of the lever used to position the cutting unit for mowing or transport.
How to adjust the cutting height using the designated lever.
Instructions for adjusting the rider's seat for comfort and positioning.
Guidelines for safely filling the fuel tank with the correct type of petrol.
Explanation of release levers and clutch controls for engaging/disengaging drive systems.
Essential checks and preparations required before starting the engine.
Step-by-step guide on how to start the engine, including cold and warm starts.
Procedure for starting the engine with a weak battery using jump leads.
Detailed steps for connecting jump leads safely to start the engine.
How to drive the Rider, including pedal usage and cutting unit engagement.
Advice for achieving optimal mowing results and best lawn care practices.
Instructions on how to properly stop the engine after use.
A comprehensive schedule of maintenance tasks and their intervals.
Guidelines for cleaning the machine after use and specific component cleaning.
Instructions for accessing the engine and components by removing machine hoods.
How to check the muffler for completeness and secure mounting.
Procedure for checking and adjusting the steering wires for proper alignment.
Steps to adjust the parking brake for FR 2213 RA, FR 2213 MA, FR 2215 MA models.
Steps to adjust the parking brake for the FR 2215 MA 4x4 model.
Procedure for adjusting the throttle cable for optimal engine response.
Instructions for replacing the air filter to ensure engine performance.
Procedure for replacing the fuel filter to maintain fuel system integrity.
How to check and clean the air filter for the fuel pump.
Importance and procedure for checking tyre pressure for optimal performance.
Information regarding the electronic ignition system and spark plug maintenance.
Detailed steps for removing, checking, and replacing the spark plug.
Locating and checking the main fuse, and procedure for replacement.
How to verify the proper functioning of the machine's safety systems.
Procedure for cleaning the engine's cooling air intake to prevent overheating.
How to adjust the cutting unit's pressure for optimal ground contact.
Procedure for checking the parallelism of the cutting unit.
Steps to adjust the cutting unit's parallelism for balanced cutting.
How to place the cutting unit in a service position for easier access.
Checking blades for sharpness, damage, and proper attachment.
Instructions on how to return the cutting unit from the service position.
Procedure for removing the mulching plug to change cutting functions.
How to check and top up the engine oil level.
Procedure for changing the engine oil at recommended intervals.
How to check and top up the transmission oil level.
Procedure for lubricating the belt adjuster with grease.
Information on lubricating various joints and controls on the machine.
Steps to prepare the machine for long-term storage, especially for winter.
Recommendations for performing service during the off-season for optimal performance.
Information about a protective cover for storage or transport.
Statement of compliance with European directives for machinery, EMC, and noise emissions.
To Next Page
