JRC JAN-9202 User Manual (English)

Other manuals for JRC JAN-9202

Instruction Manual332 pages

Field Service Manual1078 pages

Questions and Answers:

N
nmeyerAug 22, 2025
How to fix JRC Monitor when the power is not supplied?
- F
  Frank ClarkAug 22, 2025
  If the JRC Monitor is not receiving power, check the following: * Ensure the AC or DC power supply is properly connected. * Verify the breaker at the front of the power supply unit (NBD-913) is set to ON by pushing up the lever. * Confirm the AC or DC power supply input is within the specified voltage range. If these steps don't resolve the issue, the internal wiring, the power supply unit (NBD-913), the central control unit (NDC-1590), or the operation unit (NCE-5605) may be faulty, and you should request a repair from the distributor.
D
daniel02Aug 23, 2025
What to do if position information (GPS) is not displayed on JRC Monitor?
- C
  Christopher PerezAug 23, 2025
  If the GPS information isn't showing on your JRC Monitor, verify these items: 1. Ensure the communication is correctly set. 2. Check that the power supply for the GPS equipment is on. 3. Confirm the GPS equipment is performing positioning. 4. Verify the connection with the GPS equipment, checking the LED of the corresponding port if connected to the serial LAN interface circuit. 5. If connected to the serial-LAN interface circuit (CMH-2370), ensure its power supply is on. If problems persist, the serial-LAN interface circuit (CMH-2370), internal wiring, or the central control unit (NDC-1590) might be faulty, requiring a repair request from the distributor.
K
Krista RomeroAug 25, 2025
Why is my JRC Monitor screen not displaying even though the power is on?
- M
  Mr. Jesse FitzpatrickAug 26, 2025
  If your JRC Monitor has power but the screen remains blank, first, check the brightness setting and adjust it to an appropriate level. If adjusting the brightness doesn't solve the problem, the internal wiring or the display unit (NWZ-208/ NWZ-207/NWZ-214) may be faulty, and you should request a repair from the distributor.
J
joshua90Aug 27, 2025
Why is the Log not displayed correctly on my JRC Monitor?
- D
  Dawn SmithAug 27, 2025
  If the log isn't displayed correctly on your JRC Monitor, ensure the communication is set correctly. Also, check that the power supply for the log equipment is turned on and verify the connection with the log equipment, looking for the LED blinking at signal reception if connected to the serial LAN interface circuit or gyro interface circuit.
A
Andrew PhillipsAug 28, 2025
How to troubleshoot rudder angle display issues on JRC Monitor?
- A
  Aaron SimmonsAug 28, 2025
  If the rudder angles are not displayed correctly on the JRC Monitor, verify that the communication is correctly set. Also, ensure that the power supply for the rudder angle indicator is turned on and check the connection with the rudder angle indicator, looking for the LED at data reception if connected to the serial LAN interface circuit. If connected to the serial-LAN interface circuit (CMH-2370), ensure its power supply is on.
A
allenwilsonAug 30, 2025
Why is wind direction/wind speed data not showing on my JRC Monitor?
- M
  Madison CollinsAug 30, 2025
  If wind direction/wind speed data isn't displayed on your JRC Monitor, first, check that the communication is correctly set. Then, ensure the power supply for the anemoscope/anemometer is turned on. Finally, verify the connection with the anemoscope/anemometer, checking the LED of the corresponding port of the serial LAN interface circuit at data reception. Also, ensure that the power supply for the serial-LAN interface circuit (CMH-2370) is turned on.
O
owensjackieAug 31, 2025
How do I fix water depth display on my JRC Monitor?
- S
  Susan RhodesAug 31, 2025
  If water depth values aren't displayed on your JRC Monitor, confirm that the communication is correctly set. Also, ensure the power supply for the echo sounder is turned on, and verify the connection with the echo sounder, checking the LED of the corresponding port of the serial LAN interface circuit at data reception.
M
mikayla85Sep 1, 2025
What to do if UPS does not operate with JRC Monitor?
- K
  Kevin JohnsonSep 1, 2025
  If the UPS is not operating with your JRC Monitor, check the connection with the UPS and ensure it is correctly set. If the battery is extremely depleted, replace it, requesting specialized service staff for the replacement and turning off the corresponding power supply breaker in the ship during the replacement. If the issue persists, the internal wiring or the UPS itself may be faulty, requiring a repair request from the distributor.
K
Kristy BradleySep 3, 2025
Why are sensor signals not displayed on my JRC Monitor?
- C
  chaynesSep 3, 2025
  If sensor signals aren't displayed on your JRC Monitor, check that the communication is set correctly. Also, ensure the power supply for the sensor equipment is turned on and verify the connection with the sensor equipment, checking the LED of the corresponding port of the serial LAN interface circuit at data reception.
H
Hailey DrakeSep 4, 2025
Why can't I adjust the brightness on my JRC Monitor?
- S
  Sheila TaylorSep 4, 2025
  If you cannot adjust the brightness of your JRC Monitor, the display unit (NWZ-208/ NWZ-207/NWZ-214) may be faulty, and you should request a repair from the distributor.

JRC JAN-9202 Specifications

General

Type	X-band Radar
Power Supply	24 V DC
Transmitter Output Power	25 kW
Range	Up to 96 NM
Display	LCD
Power Output	25 kW
Frequency	9410 MHz ± 30 MHz
Antenna Rotation Speed	24 rpm
Beam Width	1.2°