JRC JMR-5406-X - User Manual

40 pages

To Next Page

To Next Page

Loading...

ISO 9001, ISO 14001 Certified

OCT. 2021 Edition 6CODE No.7ZPRD0955

MARINE RADARMARINE RADAR

EQUIPMENTEQUIPMENT

JMRJMR

-

54045404

-

X

JMRJMR

-

54065406

-

X

JMRJMR

-

54105410

-

4X/4XH/6X/6XH4X/4XH/6X/6XH

JMRJMR

-

54255425

-

6XH/7X/9X6XH/7X/9X

JMRJMR

-

54305430

-

S

JMRJMR

-

54725472

-

S

JMRJMR

-

54825482

-

S/SHS/SH

Not use the asbestos

For further information,contact:

URL Head office : http://www.jrc.co.jp/eng/

Marine Service Department

1-7-32 Tatsumi, Koto-ku, Tokyo 135-0053, Japan

　　　　　　　　　　　: tmsc@jrc.co.jp

　　　　　　　　　　　:

+81-50-3786-9201

e

-

mail

One

-

call

SIMPLIFIEDSIMPLIFIED

INSTRUCTIONINSTRUCTION

MANUALMANUAL

Table of Contents

Questions and Answers:

J
Jacob LiuSep 2, 2025
Why can't radar images be tuned on my JRC Marine Equipment?
- C
  Carl GriffinSep 3, 2025
  If radar images cannot be tuned on your JRC Marine Equipment, it may be because the magnetron is deteriorated significantly (if using a radar antenna that uses a magnetron). Replace the magnetron. Alternatively, coarse tuning adjustment may not have been performed correctly; perform it correctly. If a solid-state radar antenna is connected, note that a tuning bar is not displayed for this type of antenna.
J
John RileySep 3, 2025
Why is the radar image azimuth incorrect on my JRC Marine Equipment?
- A
  Ashley HenrySep 3, 2025
  If the azimuth of the radar image is not displayed correctly on your JRC Marine Equipment, it may be because the azimuth is not set correctly. Set the azimuth correctly. Alternatively, CCRP may not be set correctly; set CCRP correctly. Also, the GPS radar antenna position may not be set correctly; set it correctly.
M
Matthew HayesSep 4, 2025
Why is the radar image range incorrect on my JRC Marine Equipment?
- T
  Teresa CameronSep 4, 2025
  If the range of the radar image is not displayed correctly on your JRC Marine Equipment, it may be because the range is not set correctly. Set the range correctly. Alternatively, CCRP may not be set correctly; set CCRP correctly. Also, the GPS radar antenna position may not be set correctly; set it correctly.
C
Christopher HarrisSep 4, 2025
What to do if the display is frozen on my JRC Marine Equipment?
- A
  April PattersonSep 4, 2025
  If the display is frozen on your JRC Marine Equipment, disabling the mode selection screen, it indicates that the processing unit (NDC-1678) is abnormal and requires repair from the distributor.
M
Monica RobertsSep 4, 2025
Why can't radar images be superimposed on my JRC Marine Equipment?
- T
  Taylor PerrySep 5, 2025
  If radar images cannot be superimposed on your JRC Marine Equipment, there are several potential causes: * The connection with the radar antenna is abnormal; check the connection. * The connection with the radar indicator is abnormal; check the connection. If these steps don't resolve the issue, the internal wiring or the processing unit (NDC-1678) may be faulty, requiring repair from the distributor.
T
thompsonjaclynSep 5, 2025
Why can't I adjust the brightness on my JRC Marine Equipment monitor?
- V
  vjarvisSep 5, 2025
  If the brightness of the monitor cannot be adjusted on your JRC Marine Equipment, it indicates that the display (NWZ-208/NWZ-214) is faulty and requires repair from the distributor.
K
kathleenalvaradoSep 6, 2025
Why can't I select some menus on my JRC Marine Equipment's mode selection screen?
- S
  Shawn SchwartzSep 6, 2025
  If some menus cannot be selected on the mode selection screen of your JRC Marine Equipment, it indicates that the device license has not been installed. Request repair or additional arrangement to the supplier and install the license.
J
Joseph JohnsonSep 6, 2025
Why is the interswitch not working on my JRC Marine Equipment?
- J
  Joseph PattersonSep 6, 2025
  If interswitch does not function on your JRC Marine Equipment, there are several potential causes: * Power for the interswitch is not turned on; turn on the power for the interswitch. * The connection with the interswitch is abnormal; check the connection. If these steps don't resolve the issue, the interswitch, the terminal board circuit (CQD-2322), internal wiring, or the processing unit (NDC-1678) may be faulty, requiring repair from the distributor.
B
Brianna WashingtonSep 7, 2025
Why are contact signals not outputting from my JRC Marine Equipment?
- B
  Barbara BlackSep 7, 2025
  If contact signals are not being output by your JRC Marine Equipment, and contact signal output is acquired from the serial-LAN interface circuit, it may be because the power supply for the serial-LAN interface circuit (CMH-2370) is not turned on. Turn on the power supply for the serial-LAN interface circuit. If the issue persists, the internal wiring or the processing unit (NDC-1678) may be faulty, requiring repair from the distributor.
R
richardhernandezSep 7, 2025
Why is the cursor not displayed correctly on my JRC Marine Equipment?
- M
  Marie BrooksSep 7, 2025
  If the cursor is not displayed correctly on your JRC Marine Equipment, it indicates that the processing unit (NDC-1678) is faulty and requires repair from the distributor.

JRC JMR-5406-X Specifications

General

Screen Size	10.4 inches
Power Output	6 kW
Antenna Type	Slotted waveguide array
Operating Temperature	-15°C to +55°C
Display Type	LCD
Antenna Rotation Speed	24 or 48 RPM

Related product manuals

Preview: JRC JMR-5410-4X

JRC JMR-5410-4X

JRC JMR-5410-6X

JRC JMR-7210-6X

JRC JMR-9225-6X

JRC JMR-9230-S3

Preview: JRC JMR-92 Series

JRC JMR-92 Series