xl
目 錄
!. 規格................................................................................................................................. 2
@. 安裝................................................................................................................................. 3
1. 承托板的安裝方法 .......................................................................................................................................................... 3
2. 皮帶護罩的安裝方法 ...................................................................................................................................................... 4
3. 踏板的安裝方法 .............................................................................................................................................................. 5
4. 線架的安裝 ....................................................................................................................................................................... 6
#. 準備和運轉 .................................................................................................................... 7
1. 加油 .................................................................................................................................................................................... 8
2. 確認轉動方向 ................................................................................................................................................................. 11
3. 機針的安裝方法 ............................................................................................................................................................ 12
4. 穿線方法 ......................................................................................................................................................................... 14
5. 壓腳的調節和壓腳的拆卸 ........................................................................................................................................... 16
6. 縫距長度的調節 ............................................................................................................................................................ 17
7. 差動送布的調節 ............................................................................................................................................................ 18
$. 維修............................................................................................................................... 20
1. 切刀和包邊寬度的調整 ................................................................................................................................................ 20
2. 縫紉機頭的清掃 ............................................................................................................................................................ 23
3. 筒形濾清器的維修和更換 ........................................................................................................................................... 24
4. 調整彎針和調整護針器 ................................................................................................................................................ 26
5. 挑線桿位置尺寸（標準調整）..................................................................................................................................... 29
6. 馬達皮帶輪和皮帶 ........................................................................................................................................................ 31
xxxvii
目 次
!. 仕様 ........................................................................................................................................ 1
@. 据え付け ................................................................................................................................ 3
1. フレーム受板の取り付け方 ........................................................................................................................... 3
2. ベルトカバーの取り付け方 ........................................................................................................................... 4
3. ペダルの取り付け方 ....................................................................................................................................... 5
4. 糸立装置の取り付け方 ................................................................................................................................... 6
#. 準備および運転 .................................................................................................................... 7
1. 給油 .................................................................................................................................................................. 8
2. 回転方向の確認 ............................................................................................................................................ 11
3. 針の取り付け方 ............................................................................................................................................ 12
4. 糸の通し方 ................................................................................................................................................... 14
5. 押え圧の調節と押えの外し方 .................................................................................................................... 16
6. 縫い目長さの調節 ........................................................................................................................................ 17
7. 差動送りの調節 ............................................................................................................................................ 18
$. 保守 ..................................................................................................................................... 20
1. メスとかがり幅の調整 ................................................................................................................................ 20
2. ミシン頭部の掃除 ........................................................................................................................................ 23
3. カートリッジフィルタの点検と取りかえ ................................................................................................. 24
4. ルーパ合わせおよび針受け合わせ寸法値 ................................................................................................. 26
5. 天びん位置寸法値（標準合わせ） ............................................................................................................. 29
6. モータプーリとベルト ................................................................................................................................ 31
CONTENTS
!. SPECIFICATION ...........................................................................................................1
@. INSTALLATION .............................................................................................................3
1. Installing the frame support plate .....................................................................................................3
2. Attaching the belt cover .....................................................................................................................4
3. Installing the pedals ...........................................................................................................................5
4. Installing the thread stand .................................................................................................................6
#. PREPARATION AND OPERATION ..............................................................................7
1. Lubrication ..........................................................................................................................................8
2. Checking the direction of rotation ..................................................................................................11
3. Attaching needles .............................................................................................................................12
4. Threading the machine.....................................................................................................................14
5. Adjusting the pressure of the presser foot and removing the presser foot ...............................16
6. Adjusting the stitch length...............................................................................................................17
7. Differential feed mechanism ............................................................................................................18
$. MAINTENANCE...........................................................................................................20
1. Knives and overedge witdh .............................................................................................................20
2. Cleaning the machine head .............................................................................................................23
3. Checking the cartridge filter and replacing it.................................................................................24
4. Dimensions used to adjust the looper and the needle guard.......................................................26
5. Dimensions relatrd to the position of the thread take-up (standard adjustment) ......................29
6. Motor pulleys and belts ....................................................................................................................31
To Next Page
Loading...
Need help?
General
