JVC AX-Z1010TN - Page 6

AX-Z1010TN
1-6
(No, 20115)
@ GND terminal
@ Phono selector switch (CARTRIDGE
(= MC/ LMM)) — This switch selects be-
tween MC and MM type cartridges. When
depressed, MC is selected, When returned to
the original position MM is selected.
© PHONO terminats
@ CD terminats
@ LINE 1 terminais
@ LINE 2 terminals
@ LINE 3 terminals
@ DAT I/TAPE 2 terminals
@ TAPE 1/DAT 2, SEA terminals
@ AC voltage selector”
When this equipment is used in an area where
the supply voltage is different from the preset
voltage, reset the voltage selector to the cor-
rect position,
@ FUSE holder*
@ SPEAKERS terminals
Connect the speaker cords following the
figures.
@ AC OUTLETS**
UNSWITCHED AC outlets
@ Power cord
C5) Terminals:
DIGITAL 1: Connect the optical digital output
of CD player, etc. Connect the attached opti-
cal fiber cable after removing the connector
cover.
DIGITAL 2: Connect the coaxial digital out-
put of CD player, etc,
DAT REC: Connect the digital input of DAT
deck.
DAT PLAY: Connect the digital output of DAT
deck.
Digital coaxial cable: Use 75 ohm coaxial ca-
ble with RCA pins at both ends to connect the
DIGITAL 2 and DAT terminals.
@ COMPU LINK-1/SYNCHRO terminals
Connect to units provided with a COMPU
LINK-1/SYNCHRO terminal to let the COMPU
LINK contro! system function,
Note:
* COMPU LINK changeover switch
When operating an automatic playback
or a syncronized recording, be sure to
set this switch to the correct position to
perform desired operation.
* Not provided on units for the U.S.A., Cana-
da, Continental Europe, the U.K. and Aus-
tralia.
** Not provided on units for Continental Eu-
rope, the U. K. and Australia.
Notes:
1. Switch the power off when connecting
any component.
2. Connect source components with left
and right channels connected correctly.
Reversed channels may degrade the
stereo effect.
3. Connect speakers with correct polarity;
(+) to (+) and (—) to (—). Reversed
polarity will degrade the stereo effect.
4. Connect plugs or wires firmly. Poor con-
tact may result in hum or damage the
unit.
5. Do not connect equipment requiring
more than the rated. power to the AC
OUTLETS on the rear panel.
6. The AC OUTLETS are not switched off
when the front panei power switch is
switched off.
7. If your turntable has a separate ground
fead, connect it to the GND terminal.
8. Use speakers with the correct im-
pedance within the value indicated on
the rear panel.
9. Connection of digital signal cable
Before connecting the optical cable to
the DIGITAL 1 optical input terminal re-
move the cover from the terminal.
Since optical cable is made of pfastic or
giass material be careful not to bend
sharply.
10. When connected by COMPU LINK the
cassette deck should be connected to
the corresponding TAPE 1/DAT 2 termi-
nats on the amplifier and the DAT deck
should be connected to the correspond-
ing DAT 1/TAPE 2 terminals. Although
it is possible to connect a cassette deck
and a DAT deck with the DAT 1/TAPE 2
terminals and the TAPE 1/DAT 2 termi-
nals respectively, when connecting with
an equipment corresponding to COMPU
LINK of JVC, do not connect the COM-
PU LINK cable with the cassette deck or
the DAT deck.
11. When a JVC’s CD player is connected by
COMPU LINK in digital system, connect
to DIGITAL 1 and CD (analog system) ter-
minats of this unit, and set the COMPU
LINK changeover switch [CD | to “DIGI-
TAL” position.