JVC HR-J282EU - EEPROM IC Setting Information; EEPROM IC Setting Details

1-6
SERVICE INFORMATION FOR EEPROM IC SETTING
MODEL NAME HEX BINARY
HR-J285EU 02 00 00000000
C0 00 00000000
C0 00 00000000
B1 00 00000000
30 00 00000000
48 00 00000000
HR-J290EU E2 00 00000000
HR-J293EU C1 00 00000000
C8 00 00000000
B1 00 00000000
30 00 00000000
48 00 00000000
HR-J585EU 0C 00 00000000
C0 00 00000000
C0 00 00000000
B1 00 00000000
30 00 00000000
48 00 00000000
HR-J590EU/ EC 00 00000000
J593EU C1 00 00000000
C8 00 00000000
B1 00 00000000
30 00 00000000
48 00 00000000
HR-J595EK 2C 00 00000000
C0 00 00000000
C8 00 00000000
B4 00 00000000
00 00 00000000
43 00 00000000
HR-J595MS 6C 00 00000000
C0 00 00000000
48 00 00000000
B0 00 00000000
62 00 00000000
40 00 00000000
HR-J295MS 62 00 00000000
C0 00 00000000
48 00 00000000
B0 00 00000000
62 00 00000000
40 00 00000000
HR-J295EK 02 00 00000000
C0 00 00000000
C8 00 00000000
B4 00 00000000
00 00 00000000
43 00 00000000
HR-J282EU 02 00 00000000
C0 00 00000000
C0 00 00000000
B7 00 00000000
00 00 00000000
50 00 00000000
MODEL NAME HEX BINARY
HR-J283EU 02 00 00000000
C0 00 00000000
C8 00 00000000
B7 00 00000000
00 00 00000000
50 00 00000000
HR-J582EU 0C 00 00000000
C0 00 00000000
C0 00 00000000
B7 00 00000000
00 00 00000000
50 00 00000000
HR-J583EU 0C 00 00000000
C0 00 00000000
C8 00 00000000
B7 00 00000000
00 00 00000000
50 00 00000000
# Remote control Key action
• OK : Now option data write to EEPROM
• MENU : Menu exit
• EDIT : ▲▼ (Option data change from 0~F
Hexadecimal)
• MOVE : ▲▼ (Cursor move for option data
setting)
1. Power Cord plug-in and Power SW on, then
“EEPROM option data setting” screen to the left
will be displayed.
# If not, press the “Child lock” key on the Remote
controller to switch with “CANAL” because the
VCR set has “CANAL IC” inside.
# If your VCR set has “NTSC Line Record”, switch
the VCR set to “AV” mode after inputting the Line
Video signal. If not, the Blue back screen may be
shown in to screen.
2. Refer to option data in the next page and input
the value to the “HEX” field using “EDIT” key
only, and then press the “OK” key on the Remote
controller.
3. Check the basic operation
(Tuner/PB/CUE/REV/AV/REC mode...)
4. Initialize the EEPROM IC pressing the “REC” key
on the Front Panel and “CLEAR” key on the
Remote controller at the same time.
▲
▲
EEPROM option code No. setting
EEPROM option code No. setting procedure