1
KW-XR616
Installation/Connection Manual
/
ENGLISH /
0110DTSMDTJEIN
EN, TH
© 2010 Victor Company of Japan, Limited
GET0666-010A
[UH]
INSTALLATION /
• To prevent short circuits:
– Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.
– Cover the terminals of the UNUSED leads with insulating tape.
• Be sure to ground this unit to the car’s chassis again after installation.
• Replace the fuse with one of the specified rating.
• Connect speakers with a maximum power of more than 50 W (impedance of
4 Ω to 8 Ω). Otherwise, change the <AMP GAIN> setting. (See page 25 of the
INSTRUCTIONS.)
• The heat sink becomes very hot after use. Be careful not to touch it when
removing this unit.
•
:
–
–
•
•
• 50 W ( 4 Ω 8 Ω)
<AMP GAIN> (
25 )
•
12 V DC, NEGATIVE ground /
12 V,
To the car system /
You need the installation kits which corresponds to your car. /
Check the battery system in your car /
WARNINGS /
The following illustration shows a typical installation. If you have any questions or require information
regarding installation kits, consult your JVC car audio dealer or a company supplying kits.
JVC
PRECAUTIONS on power supply and speaker connections
• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be
seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in
your car.
•
•
• The fuse blows.
]
Are the red and black leads connected correctly?
• Power cannot be turned on.
]
Is the yellow lead connected?
• No sound from the speakers.
]
Is the speaker output lead short-circuited?
• “PROTECT” appears on the display and no operation can be done.
]
Is the speaker output lead
short-circuited or touches the chassis of the car/head unit? ; Have you reset your unit?
• Sound is distorted.
]
Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers
grounded in common?
• Noise interfere with sounds.
]
Is the rear ground terminal connected to the car’s chassis using shorter
and thicker cords?
• This unit becomes hot.
]
Is the speaker output lead grounded? ; Are the “–” terminals of L and R
speakers grounded in common?
• This unit does not work at all.
]
Have you reset your unit?
TROUBLESHOOTING /
•
]
?
•
]
?
•
]
?
• “PROTECT”
]
/
? ;
?
•
]
? ;
“–” L () R ()
?
•
]
?
•
]
? ;
“–” L () R ()
?
•
]
?
Heat sink /
In-dash mounting /
In-dash
Audio system originally installed in the car /
Car dashboard /
If there is an interfering tab on
the mounting bracket, bent it
flat. /
Screw removed from the car /
Mounting bracket removed from the car /
Firmly attach the ground wire to the metallic body of the car using the screw originally
fixed to the metallic body of the car. /
Installing with the mounting brackets from the car /
Install the unit at an angle of less than 30˚.
30˚
Part list /
A Flat countersunk screws—M5 × 8 mm /
—M5 × 8 . (×8)
B Round head screws—M5 × 8 mm / —
M5 × 8 . (×8)
C Plate for use with a Nissan car /
(×1)
D Power cord / (×1)
When installing the unit in a Nissan
car /
Fix the supplied plate as illutrated. /
Install_KW-XR616_010A_f.indd 1Install_KW-XR616_010A_f.indd 1 2/1/10 12:53:27 PM2/1/10 12:53:27 PM
To Next Page
Need help?
General
