JVC RX-807VTN

6-L (€EEO7 “ON)
to AM or FM Broadcasts
ter
® Tuning in a Station
1.Press the AM or FM key.
2. Use the TUNING keys to find a station.
—$§ wing ——
* While tuning in an FM station, press the FM MODE/MUTE key
to light the MUTE/AUTO indicator, this cuts out inter station noise
while tuning. ch
mot
te a Ee
MUTE
AUTO
Each time the TUNING keys are pressed, the frequency is varied
in steps of 10 kHz for AM and 0.1 MHz for FM. The setting will
vary continuously while the keys are pressed and held.
Auto-tuning starts when the TUNING keys are released and stops
when a station is tuned. To halt auto-tuning, press a TUNING key.
ch
Og Ss
feo:3) BOTS
The TUNED indicator will light when a station is tuned in correctly.
« Adjust the antenna if the indicator does not light.
@ The STEREO indicator will light when an FM stereo station is tuned
in correctly.
If the FM stereo station is weak and noisy, press the FM
MODE/MUTE key again to turn off the MUTE/AUTO indicator to
improve reception (broadcast becomes monaural).
@ Presetting Stations
You can preset a total of 40 AM and FM station (CH 1 through CH 40)
1, Tune in the desired station with the TUNING keys.
FM OI we
tsreneo) XUTS
2. Press the MEMORY key to light its indicator
Ls MEMORY ~~
FM a tL iC mie
“il
(STERES) UTS
3. Enter the channel number with numeric keys while the indicator
is On (for about 5 seconds)
ee
—— | ich
aor
a rw Gm
aER muTe
@ If the indicator turns off before you enter the channel number,
press the MEMORY key again.
4. Repeat this procedure to preset other channels.
= Auto Memory
The auto-memory feature scans frequencies upward and presets sta-
tions as they are tuned, in ascending channel number order.
1. Using the TUNING keys, select the frequency from which you want
auto-memory to start {the lower-limit frequency)
2. Press the AUTO MEMORY key to light its indicator
AUTO.
1 Ear - ch
Nel ATS =
mors.
Enter the starting channel number with the numeric keys while
the indicator is on (about 5 seconds}
ee
oa Sekar ich
FM a7 &
Fy 1S =
ry
@ |f the indicator turns off before you enter the channel number,
press the AUTO MEMORY key again
3. The auto-memory feature starts scanning frequencies upward
The TUNED indicator will light when a station is tuned, with the
channel number blinking (for about 5 seconds).
AUTO. i
MEMORY ich
FM ate
Gi5
Hin
A. The presetting is complete when the MEMORY indicator is lit.
AUTO. fg
MEMORY MEMORY fch
FM @ | 5 Mie
This continues until the upper-limnit frequency is reached or all 40
channels are filled
Note:
If you do not want to preset a station, resume scanning by pressing
the AUTO MEMORY key while the channel number is blinking. To
halt the auto-memory feature, press any TUNER key other than the
AUTO MEMORY key.
= Selecting preset channels
1. Press numeric keys to select a preset channei
ca an |
RH aS oy ane i
cite .
@ To indicate numbers 1 through 10, simply press the appropriate
keys.
To indicate numbers over 10, press the appropriate combination
of keys.
Examples;
To indicate 17, press ‘’+10'', then "7".
To indicate 20, press ‘’+10’’, then "10".
To indicate 26, press ‘+ 10’ twice, then ''6"’.
To indicate 40, press ‘+ 10" three times, then ''10"’.
You can designate the preset channel number using the remote con-
trol unit.
1. Press the TUNER key of the Function Select keys on the internal panet.
2. Use the following keys.
1~10, +10: Enters the preset channel number.
PRESET CHANNEL
+ : Scans to higher preset channels
- : Scans to lower preset channels
NLAZO8-Xu