JVC TD-V711 Service Manual

TD-V711 A/B/C/E/G/J/U
[5]
Removal
of
Main
Parts
Cabinet Section
@ Top Cover
1) Remove four screws on both sides.
2) Remove two screws fixing the back.
@ Bottom Cover
1) Remove six screws @) and a).
[Main/power source base parts can be replaced in this
condition]
@ Front Plate
1} Remove INPUT LEVEL voiume knob and BIAS/BALANCE
knob.
2) Remove five screws (2) fixing the front panel.
@ Front Panel Ass‘y
1) Remove power switch knob.
2) Remove switch side of input switch remote bar and
remove knob.
3)
Pull
input
volume
remote
bar
inside
and
remove
from
front
panel.
4)
Remove
two
screws
(3)
fixing
the
center
chassis
from
the
front.
5) Remove four screws (4) on both sides.
6) Remove wires if necessary.
@ Removal from Front Panel
Mechanism Ass‘y
1) Remove two screws fixing mechansim ass’y top.
2) Remove LED lead soldering on leaf switch base.
3) Remove two screws 6) fixing mechanism ass’y bottom.
4) Open cassette door and remove.
Timer Switch
Remove four pawls (A) fixisng the switch base.
Headphone jack Base
1) Pull out output volume knob.
2) Remove nut fixing the jack.
3)
Remove
volume
bracket,
push
up
volume
shaft
and
remove
from
groove.
Volume Base
1)
Remove
two
pawls
fixing
the
BIAS
adjustment
volume/BALANCE volume base.
Display,
DOLBY
B/C NR,
HX,
MPX
Switch
Base
1)
Remove
two
scrws.
@)
fixing
the
switch.
2)
Remove
six
pawls
©)
fixing
the
base.
Inside view
Fig. 5-4
Switch Base Ass’y
Remove
pawl
©)
,
then
remove
five
pawls
©
pawls
from (©) side in order.
Push base from front panel hole for easier removal.
(No. 4294) 6
Mechansim Section
@ Head parts
1)
To
remove
head
block,
remove
three
screws
@)
@)
3)
.
2)
To
remove
erasing
head,
remove
one
screw
3)
To
remove
playback
head,
remove
three
special
nuts
(5)
;
then
remove
playback
head
base
and
remove
two
screws
Caution:
A
spring
will
come
off
when
removing
playback
head.
4)
To
remove
record/playback
head.
(1)
Remove
playback
head.
(2)
Remove
three
screws
M®Ee
fixing
record/playback head.
Caution:
Springs
@@)
are
the
same
and
@)
is
different.
(Springs Q) and 6) are the same)
@ DD Motor Ass’y
1) Remove two screws ;
2)
Remove
two
screws
from
both
sides
of
the
chassis.
3)
Slide
idler
to
right
and
lift
chassis
to
remove.
@ Cam Motor
Remove two screws a2 a3 ‘
@ Reel Motor
Remove two screws (5) :
@ Cam Switch
1) Remove one screw :
2) Slide brake and pull out.
(Cautions for assembling)
(1) Align car gear and cam switch holes.
(2)
Head
base
arm
stud
must
match
cam
switch
gear
groove.
@ Pinch Roller
1) Remove left hexagon nut a? ,
2)
Remove
arm
hooked
on
chassis
on
right.
(Only
push
arm
as
required
to
remove)
® is playback head in-
Stalling position adjusting
.
screw.
(to
move
playback
Fig.
5-5
head
back
and
forth)
Brake (Slide position)
Push arm to remove
(Only push as required to
remove)
Fig. 5-8

JVC TD-V711 Specifications

General

Brand	JVC
Model	TD-V711
Category	Cassette Player
Language	English