JVC UX-M3R User Manual

– 17 –
Using the Timers
There are three timers available – daily timer, recording timer
and sleep timer.
Before using the timers, you need to set the built-in clock.
(See page 8.)
Using Daily Timer
With the daily timer, you can wake to your favorite music or
radio program.
How the daily timer actually works
At the timer-on time, the unit automatically turns on, sets the
volume to the preset level, and starts playing the specified
source (radio or CD). Then, at the timer-off time, the unit
automatically turns off (on standby).
The timer setting remains in memory until you change it.
• There is a time limit in doing the following steps. If the
setting is canceled before you finish, start from step 1
again.
1 Press and hold DISPLAY
MODE until “ ON” starts
blinking on the display, then
press PROGRAM.
The hour indication starts blinking.
2 Press 4 or ¢ to set the
timer start hour, then press
PROGRAM.
The minute indication starts blinking.
3 Press 4 or ¢ to set the
minute, then press
PROGRAM.
“ ON” starts blinking again.
4 Press DISPLAY MODE so
that “ OFF” starts
blinking on the display, then
press PROGRAM.
The hour indication starts blinking.
5 Set the time to stop playback
following the same
procedure as steps 2 and 3.
6 Press DISPLAY MODE so
that “TUNER,” “TAPE,”
“CD” or “REC TU” appears
on the display, then press
PROGRAM.
7 Press 4 or ¢ to select
the desired source, then
press PROGRAM.
8 Prepare the source and set the volume.
To listen to the radio, tune in the desired station.
To listen to a CD, load the disc.
9 Press TIMER ON/OFF SET
(or TIMER on the remote
control) to activate the timer.
“ ” lights up on the display.
10 Turn off the unit (on standby).
When the preset time is reached, the
selected source is played if the timer
has been activated.
To deactivate the timer, press TIMER ON/OFF SET (or
TIMER on the remote control).
“ ” disappears from the display.
• The timer-off function is not activated if the starting and
stopping times are the same.
• If the selected source (CD or TAPE) is not available when
preset timer is reached, TUNER is selected automatically.
Timer Recording
You can use the recording timer to record a preset radio
station from a specified time and for a specified duration
automatically.
1 Load a recordable tape into the tape deck.
Insert a tape with the open side down and the side to be
recorded facing out from the unit.
2 Follow the “Using Daily Timer” procedure on
the left. Select “REC TU” as the source for
timer recording.
• If the preset time is reached while the unit is on, the timer
is not activated for timer recording.
• The recording timer is canceled once the recording is
finished.
DISPLAY
MODE
PROGRAM
SEARCH/TUNING
SEARCH/TUNING
DISPLAY
MODE
PROGRAM
DISPLAY
MODE
PROGRAM
SEARCH/TUNING
TIMER
ON/OFF
SET
STANDBY
/ON
02_01_21_UXM3R_A_En.p65 02.1.21, 7:24 PM17

JVC UX-M3R Specifications

Amplifier Specifications

output power	24 W (12 W + 12 W) at 8 Ω (MAX.)
output power at THD	20 W (10 W + 10 W) at 8 Ω (10% THD)
audio output level	800 mV/32 Ω
speakers impedance	8 Ω - 16 Ω

Tuner Specifications

FM tuning range	87.50 MHz - 108.00 MHz
MW tuning range	522 kHz - 1 629 kHz

CD Player Specifications

dynamic range	60 dB
signal-to-noise ratio	60 dB
wow and flutter	Unmeasurable

Cassette Deck Specifications

frequency response for normal tape	100 Hz - 10 000 Hz
wow and flutter	0.35% (WRMS)

General Specifications

power requirement	AC 240 V, 50 Hz
power consumption (operation mode)	30 W
power consumption (standby mode)	1.5 W
dimensions	160 mm × 269.5 mm × 300 mm
mass	4.3 kg

Speaker Specifications

speaker unit (woofer)	10.2 cm cone × 1
speaker unit (tweeter)	5.1 cm cone × 1
impedance	8 Ω
dimensions	160 mm × 269.5 mm × 192 mm
mass	2 kg/each