Need help?Do you have a question about the kansai WX8800 and is the answer not in the manual?
Select the correct needle type and size for the fabric and thread.
Procedure for correctly installing a new needle, ensuring proper orientation.
Correctly thread the machine to avoid stitching issues like skipped stitches or breakage.
Details on maximum and standard operating speeds and pulley direction.
Information on motor type, belt type, and pulley selection for speed adjustment.
Specifies the recommended genuine oil for the machine and its part number.
Instructions for filling the machine with oil and checking oil flow.
Procedure for changing the machine oil and filter element for extended life.
Provides physical dimensions of the machine head and its weight.
Steps to correctly mount the machine head onto the table using rubber cushions.
Guidance on cutting the machine table for specific components like the EMK type.
Procedure to set the correct angle and height for installing the looper.
Adjusting the looper's side-to-side path relative to the needles.
Setting the distance from the looper point to the needle bar.
Adjusting the vertical position of the needle relative to the looper.
Ensuring correct front-to-back clearance between needles and looper.
Adjusting the looper's circular path for optimal stitch formation.
Adjusting the extent of the looper's front-to-back travel.
Aligning the rear needle guard correctly with the needle and looper.
Setting the correct clearance for the front needle guard.
Adjusting the height and left-to-right position of the spreader.
Setting the correct clearance for the spreader thread guides.
Adjusting the timing of the spreader relative to the needles.
Specific position adjustments for spreader on WX8842 and 8842-1 models.
Specific guide position adjustments for WX8842 and 8842-1 models.
Adjusting the height and tilt of the feed dogs for proper fabric feeding.
Procedure for adjusting the stitch length using the push button and handwheel.
Setting normal and reverse differential feed ratios for fabric gathering or stretching.
Adjusting presser foot pressure for uniform stitches and fabric feeding.
Setting the presser foot and lift height relative to the needle plate and spreader.
Adjusting the height of needle thread guides for proper thread tension.
Setting the position of the thread guide on the needle thread take-up.
Synchronizing the needle thread take-up with needle bar movement.
Adjusting the needle thread guard for different thread types.
Positioning the thread guide on the spreader thread take-up.
Aligning thread guides on the looper thread take-up.
Adjusting the looper thread take-up for correct thread delivery.
Instructions for inserting lace or elastic correctly into the feeder.
Adjusting the tape guide and upper knife guide on the presser foot.
Modifying the front of the presser foot for different fabric and elastic types.
Procedure for installing the tape guide, adjusting its position and stopper.
Adjusting the feeding amount and range for lace or elastic.
Adjusting the pressure of the small roller for stretchable or non-stretchable elastic.
Troubleshooting steps if the elastic feeder is not working correctly.
Instructions for adding grease to specific parts of the EMK device.
Adjusting the position of the lower knife holder and oiling the mechanism.
Step-by-step guide to removing and installing a new lower knife.
Procedure for removing and installing a new upper knife.
Setting the correct overlap between the upper and lower knives for cutting.
Guidance on sharpening the lower knife or replacing the upper knife when dull.
Steps to remove the timing belt from the machine.
Procedure for installing a new timing belt and ensuring proper alignment.
Connecting the power supply cord and identifying wire colors for terminals.
Connecting the intermediate cords for the tape cutter.
Adjusting the cutter height and overlapping for the electric type tape cutter.
Connecting air tubes and electric cords for the air type tape cutter.
Setting the correct air pressure for the tape cutter regulator.
Adjusting cutter height, overlap, and power for the air type tape cutter.
General| Brand | kansai |
|---|---|
| Model | WX8800 |
| Category | Sewing Machine |
| Language | English |
To Next Page
