Kärcher BP 3 Home User Manual

– 1
Dear Customer.
Please read and comply with these origi-
nal operating instructions and the en-
closed safety instructions. Proceed ac-
cordingly. Keep both booklets for future reference or
subsequent owners.
This appliance has been designed for use in private
households and is not intended for commercial use.
The manufacturer is not responsible for any damages
that may occur on account of improper use or wrong op-
erations.
The device is meant for use as house water tank.
This unit is only to be used indoors.
Note
The pump is not suited for increasing the existing line
pressure.
 Used water
 Well water
 Water source
 Rain water
 Water from swimming pool (provided the dosing of
additives is proper)
The packaging material can be recycled.
Please do not place the packaging into the or-
dinary refuse for disposal, but arrange for the
proper recycling.
Old appliances contain valuable materials that
can be recycled. Please arrange for the proper
recycling of old appliances. Please dispose
your old appliances using appropriate collec-
tion systems.
Notes about the ingredients (REACH)
You will find current information about the ingredients
at:
www.kaercher.com/REACH
The warranty terms published by the relevant sales
company are applicable in each country. We will repair
potential failures of your appliance within the warranty
period free of charge, provided that such failure is
caused by faulty material or defects in manufacturing. In
the event of a warranty claim please contact your dealer
or the nearest authorized Customer Service centre.
Please submit the proof of purchase.
Illustration
1 Backflow valve
2 Connection adapter for pumps G1
3 Stopper
4 Connection G1(33.3mm) Suction pipe
5 Filling nozzle
6 Connection G1(33.3mm) Pressure pipe
7 Carrying handle*
8 Power switch*
9 Air valve (Schrader valve) with cap
10 Base with slotted hole for bolted connection
11 Pressure display
12 Drain screw
13 Power cord with plug
* only for BP 3 Home
 Check max. air pressure in the storage tank prior to
commissioning. If necessary, refill up to 2.0 bar
with a commercially available air pump with the
system switched off / zero-pressure state.
 Secure device against slipping off (fix it with
screws, if needed).
 Remove the plug.
 Screw the connection adapter in the suction con-
nection of the pump (inlet).
Tighten manually.
 Screw check valve onto connector adapter at the
suction connection.
Tighten manually.
 Connect the vacuum-proof suction hose with inte-
grated backflow stop on the suction side.
(available as optional accessory)
 Screw the connection adapter in the delivery con-
nection of the pump (outlet).
Tighten manually.
 Connect delivery line.
Illustration
 Unscrew the lid of the filling nozzle and fill in water
till it overflows.
 Screw on the lid on the filling nozzle.
 Open existing shutoff valves in the pressure pipe.
Note
Even the smallest of leakage leads to malfunctioning.
 In case of leaks, seal all connections with a suitable
sealant (e.g. Teflon tape) to prevent malfunction
due to leakage or air intake.
Contents
General information EN 1
Operation EN 1
Maintenance and Care EN 2
Transport EN 2
Storage EN 2
Special accessories EN 3
Troubleshooting EN 4
Technical specifications EN 5
General information
Proper use
Approved fluids
Environmental protection
Warranty
Operation
Description of the Appliance
Preparing the Appliance
10 EN
Ташев-Галвинг ООД
www.tashev-galving.com

Kärcher BP 3 Home Specifications

General

Type	Booster pump
Proper use	Water purification
Product color	Black, Yellow
Housing material	Stainless steel
Suitable for indoor use	Yes
Suitable for outdoor use	-
Flow rate	3000 l/h
Maximum suction height	7 m
Maximum delivery height	36 m
Maximum operating pressure	3.6 bar
Maximum input water temperature	35 °C
Power cable type	H05RN-F
Power source type	AC
Cable length	1 m
Connecting thread type	G1

Weight and Dimensions

Depth	450 mm
Width	270 mm
Height	550 mm
Weight	11300 g