Why is there no water exiting from the nozzle of my Kärcher Floor Machine?
If no water is coming out of the nozzle of your Kärcher Floor Machine, ensure the appliance switch is set to normal operation. Fill the fresh water tank with hot water (max. 60°C) and rinse the nozzle. If needed, replace the nozzle. Also, make sure the fresh water reservoir is full and that the sieve in the fresh water reservoir is clean.
What to do if the brush does not turn on my Kärcher BRC 30/15 C?
If the brush on your Kärcher Floor Machine isn't turning, verify that the appliance switch is set to normal operation. Additionally, reset the brush drive fuse on the control panel. Check the drive belt and replace it if necessary.
How to improve vacuum performance on my Kärcher BRC 30/15 C Floor Machine?
To improve the vacuum performance of your Kärcher Floor Machine: * Clean the vacuum bar. * Check, clean, or replace the seal on the dome. * Empty the dirt water reservoir. * Ensure the suction hose is properly inserted on the dome. * Inspect the suction hose for any damages.
What to do if my Kärcher Floor Machine has no power?
If your Kärcher Floor Machine isn't powering on, first, ensure the cord is properly plugged in. Next, check your building's circuit breaker and reset it if it has tripped. If these steps don't resolve the issue, the switch or power cord may be faulty, requiring professional service.
Why is suction poor on my Kärcher Floor Machine even though the motor runs?
If the vacuum motor of your Kärcher Floor Machine is running but suction is weak, check for debris lodged in the vac shoe and remove it. Also, inspect the dome gasket; replace it if it's defective or missing. Examine the vacuum hose for cracks or a loose cuff, and repair or replace as needed. Finally, ensure the recovery tank isn't full; if it is, turn off the vacuum motor and drain and rinse the tank.
What to do if the brush on my Kärcher Floor Machine does not spin?
If the brush on your Kärcher Floor Machine isn't spinning, first ensure that the switch isn't in accessory mode; switch it to the deep clean position. Then, check the brush circuit breaker and reset it if tripped. If the issue persists, the brush belt may be broken and need replacement, or the brush motor could be faulty, requiring professional service.
Why is there poor or no water flow in my Kärcher Floor Machine, causing streaky carpets?
If your Kärcher Floor Machine has poor or no water flow, resulting in streaky carpets, ensure the machine is not in accessory mode; switch it to the deep clean position. Check the jets for clogs or if they are missing. If clogged, clean them. Also, inspect the solution filter for clogs; if clogged, drain the solution tank and clean the filter. If these steps don't work, the solution pump may be faulty and require professional service.
What to do if my Kärcher Floor Machine's vacuum motor will not run?
If the vacuum motor on your Kärcher Floor Machine won't run, check if the vacuum circuit breaker has tripped and reset it. If that doesn't work, the main switch might be faulty, or there could be loose wiring or a faulty vacuum motor, all requiring professional service.
How to clean carpet that is not getting clean with Kärcher Floor Machine?
If your carpet isn't getting clean using the Kärcher Floor Machine, especially in severe soil conditions, make several passes at right angles to each other. It may also help to use a pre-spray.
What to do if my carpet is not getting wet with Kärcher Floor Machine?
If your carpet isn't getting wet when using the Kärcher Floor Machine, first check the solution filter screen inside the lower tank for clogs and clean it. Also, inspect the spray jet for clogs and clean or replace it, avoiding the use of wire. Then, check for and correct any loose wires to the pump, repairing or replacing as necessary. Finally, the solution switch might be faulty and need replacement in the handle.
General| Brand | Kärcher |
|---|---|
| Model | BRC 30/15 C |
| Category | Floor Machine |
| Language | English |
To Next Page
