Kärcher HDS 13/35 De Tr1

Other manuals for Kärcher HDS 13/35 De Tr1

Service Manual206 pages

Questions and Answers

J
John HarrisSep 23, 2025
Why is there no display after switching on my Kärcher Pressure Washer?
- M
  Mark JonesSep 23, 2025
  If there is no display after switching on your Kärcher Pressure Washer, the battery might be depleted (charge the battery). Also, check for a blown fuse (replace the fuse). Ensure the front cover is closed. Verify that the emergency stop switch is not depressed (unlock it by pulling). It's also possible there's no power supply to the inverter due to battery undervoltage or overvoltage (check the battery and charge if necessary), or the inverter itself could be defective (replace the inverter).
L
Lisa WilliamsAug 23, 2025
What causes a motor oil pressure error in my Kärcher Pressure Washer?
- A
  Amanda RichmondAug 23, 2025
  A motor oil pressure error on your Kärcher Pressure Washer can be caused by several factors. The oil level in the motor might be low, or the motor oil could have the wrong viscosity grade. Additionally, the oil pressure switch, relay K5, or relay K9 might be defective.
E
evelyntrevinoAug 25, 2025
What does ERROR 5 mean on my Kärcher Pressure Washer?
- D
  Daniel JohnsAug 26, 2025
  A flow or pressure switch error in your Kärcher Pressure Washer can arise from various causes. In normal mode, the flow and pressure switch may not run synchronously. In frost protection mode, they might run synchronously. There could be air in the system, or the fine filter before the pump might be soiled. Other potential causes include no flow or pressure, a defective or soiled reed switch flow monitor, a defective pressure switch, a defective overflow device, or a defective check valve on the high-pressure outlet.
T
Tanya RojasAug 27, 2025
What does ERROR 11 mean on my Kärcher HDS 13/35 De Tr1 Pressure Washer?
- D
  Deanna WhiteAug 27, 2025
  If your Kärcher Pressure Washer shows a flame sensor image bright blind error, it could be due to several reasons. The nozzle holder or ignition electrodes might be soiled or incorrectly adjusted. The flame sensor itself could be defective. Other potential causes include a defective fuel pump or coupling, a defective solenoid valve, a faulty ignition transformer, or a defective blower motor.
M
michelledavisAug 27, 2025
What causes ERROR 9 on a Kärcher HDS 13/35 De Tr1?
- M
  Michael MorrisAug 27, 2025
  An emission temperature error on your Kärcher Pressure Washer can be caused by a defective thermostat or temperature switch. The burner may also be wrongly set, or the heating coil could be sooted or have internal deposits. Check these components to resolve the issue.
D
David OdomSep 18, 2025
What to do if my Kärcher Pressure Washer stops and the display switches off?
- L
  lwalkerSep 18, 2025
  If your Kärcher Pressure Washer stops and the display switches off, it could be due to a blown fuse (replace the fuse). Another possibility is no power supply to the inverter because of battery undervoltage or overvoltage (check the battery and charge if necessary). Finally, the inverter itself might be defective and need replacement.
T
thomas81Sep 15, 2025
What does it mean when my Kärcher Pressure Washer shows ERROR 14 Switch-off after 45 minutes continuous break?
- C
  cassandrafrostSep 15, 2025
  If your Kärcher Pressure Washer displays ERROR 14, indicating a switch-off after 45 minutes of continuous break, it means the standby time of 45 minutes has been exceeded. To resolve this, turn the appliance off and back on.
C
Cynthia RobertsSep 16, 2025
What does it mean when my Kärcher Pressure Washer shows ERROR 15 Switch-off after 45 minutes continuous operation?
- L
  Luke MoralesSep 16, 2025
  If your Kärcher Pressure Washer displays ERROR 15, indicating a switch-off after 45 minutes of continuous operation, it means the standby time of 45 minutes has been exceeded. To resolve this, turn the appliance off and back on.
E
erin44Sep 6, 2025
How to fix ERROR 3 Temperature water inlet or cooling water on Kärcher Pressure Washer?
- L
  Larry HarrisSep 6, 2025
  If your Kärcher Pressure Washer displays ERROR 3, which relates to the temperature of the water inlet or cooling water, there could be several reasons. If the water temperature in the float container is too high due to circulation mode, allow the water to cool down or drain it. If the temperature sensor has switched off the device, turn the appliance off and back on; if the malfunction re-occurs, contact customer service. Other causes may include a defective temperature sensor (replace it), low coolant level (fill coolant into the expansion tank), insufficient V-belt tension on the fan (retension the V-belt), or a defective temperature sensor on the motor (replace the temperature sensor).
M
Michael MillsSep 3, 2025
How to troubleshoot ERROR 7 Motor oil pressure on my Kärcher Pressure Washer?
- J
  jacobdavisSep 3, 2025
  If your Kärcher Pressure Washer displays ERROR 7, indicating a motor oil pressure issue, first check the oil level in the motor and refill if it's low. Also, ensure the motor oil has the correct viscosity grade; if not, perform an oil change. The oil pressure switch on the motor might be defective, requiring replacement. If none of these solutions work, there may be motor trouble; in this case, check the motor.