EasyManuals Logo

Keith McMillen Instruments SoftStep User Manual

Keith McMillen Instruments SoftStep
89 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #56 background imageLoading...
Page #56 background image
Long Trig
Pressing and holding the key for 1 second will output a 127 followed by a 0 (100ms later).
Off Trig
(Hosted mode only)
Outputs a 127 followed by a 0 (100ms later) when the key is released.
Fast Trig Latch
(Hosted mode only)
Immediately outputs a 127 when the key is pressed. Does not go back to 0.
Dbl Trig Latch
(Hosted mode only)
Two quick presses of the key will output a 127. Does not go back to 0.
Long Trig Latch
(Hosted mode only)
Pressing and holding the key for 1 second will output a 127. Does not go back to 0.
Pedal
If an expression pedal is connected, this source will output the current value coming from the
pedal.
Range: 0-127
Init
(Standalone mode only)
Outputs a 127 whenever the current preset is loaded. Useful for initializing values whenever a
speciÞc preset is loaded. Use the min and max options (or offset) in the modlines to send a speciÞc
value.
Nav Yx10 & Key
Works in tandem with the Nav Pad. The Nav Pad must also be in Program Change mode or using
the Nav Y Decade source.
The Nav Pad’s current counter value is multiplied by 10 to get a “decade” —!e.g. 20s, 30s, 40s, etc.,
then the key number (this source is placed on) is added to the value when pressed.
Appendix 56
ロング・トリガー(LongTrig)
 キーを 1 秒間長押しすると、127 の値を出力した直後(100ms 後)に 0 の値を出力します。
オフ・トリガー(OffTrig)
(ホステッド・モードのみ)
 キーを離すと、127 の値を出力した直後(100ms 後)に 0 の値を出力します。
ファースト・トリガー・ラッチ(FastTrigLatch)
(ホステッド・モードのみ)
 キーを押すとすぐに 127 の値を出力します。値は 0 に戻りません。
ダブル・トリガー・ラッチ(DblTrigLatch)
(ホステッド・モードのみ)
 キーを素早く 2 回押すと 127 の値を出力します。値は 0 に戻りません。
ロング・トリガー・ラッチ(LongTrigLatch)
(ホステッド・モードのみ)
 キーを 1 秒間長押しすると 127 の値を出力します。値は 0 に戻りません。
ペダル(Pedal)
 エクスプレッション・ペダルを接続すると、ペダルの設定値に応じた値を出力します。
●範囲:0 127
イニット(Init)
(スタンドアローン・モードのみ)
 プリセットをロードした時に必ず 127 の値を出力します。特定のプリセットをロードした時に値を
初期化したい場合に便利です。特定の値を送信したい場合は、モッドラインのミニマムとマキシマム
(あるいはオフセット)のオプションで設定してください。
ナブ Yx10&キー(NavYx10&Key)
 ナブ・パッドとの組み合わせで動作します。ナブ・パッドは必ずプログラム・チェンジ・モードか、
またはナブ Y ディケイド(NavYDecade)・ソースを使用する設定にしておいてください。
 ナブ・パッドのカウント値は “10 の位” すなわち 20、30、40 などの値を入力するために 10 倍され
ます。そして、(このソースが割り当てられた)キーを押した時に、そのキーの番号が値に加算されます。

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Keith McMillen Instruments SoftStep and is the answer not in the manual?

Keith McMillen Instruments SoftStep Specifications

General IconGeneral
BrandKeith McMillen Instruments
ModelSoftStep
CategoryAccessories
LanguageEnglish