Kenmore 35932 - User Manual

Questions and Answers

H
hoovergregoryAug 13, 2025
Why is my Kenmore 35932 Air Conditioner not cooling enough?
- D
  Danielle DixonAug 13, 2025
  If your Kenmore Air Conditioner isn't cooling sufficiently, try these steps: First, check that the FAN SPEED is set to HI. Next, lower the TEMP Control to a cooler setting. If the room temperature is below 70°F (21°C), cooling might not be effective until the room warms up. Also, ensure the temperature sensing tube isn't touching the evaporator coil behind the front grille; if it is, straighten it away from the coil.
N
Nicholas MaloneAug 16, 2025
What to do if my Kenmore 35932 won't turn on?
- L
  Lee WilliamsAug 17, 2025
  If your Kenmore Air Conditioner isn't turning on, try the following: First, press the RESET button on the power cord plug. If it doesn't stay engaged, stop using the unit and contact a qualified technician. Ensure the plug is firmly pushed into the wall outlet. Check the fuse and replace it with a time delay type or reset the circuit breaker. Also, make sure you push the power button. Try setting the unit off, waiting 3 minutes, and then restarting it. Finally, ensure the TEMP Control is set to a lower number.
M
michael34Aug 20, 2025
What to do if Kenmore 35932 is dripping water inside?
- T
  Timothy RuizAug 20, 2025
  If your Kenmore Air Conditioner is dripping water inside the room when it's cooling, it might be improperly installed. Tilt the air conditioner slightly to the outside to allow for water drainage. Refer to the installation instructions or consult with the installer.
J
Jennifer StephensAug 25, 2025
Why is my Kenmore Air Conditioner dripping water outside?
- M
  Matthew YatesAug 25, 2025
  If your Kenmore Air Conditioner is dripping water outside when it's cooling, it's likely because the unit is removing a lot of moisture from a humid room. This is normal during very humid days.
Y
yhaysAug 27, 2025
Why is my Kenmore 35932 cooling but the room is too warm?
- D
  Deborah HillAug 27, 2025
  If your Kenmore Air Conditioner is running but the room is still too warm, consider these possible causes: A dirty air filter restricts airflow, so clean it. Set the TEMP Control to a lower temperature. Obstructions like drapes or furniture may be blocking the front of the unit, so clear any blockage. Open doors or windows can let cold air escape, so close them. Finally, allow extra time for the unit to remove stored heat from walls, ceiling, floor and furniture.
J
Jack MartinezAug 31, 2025
What to do if Kenmore Air Conditioner is cooling, but room is too warm and ice is forming?
- S
  Savannah JonesAug 31, 2025
  If your Kenmore Air Conditioner is cooling, but the room is too warm and ice is forming on the cooling coil, it might be due to the outdoor temperature being below 70°F (21°C). To defrost the coil, set the MODE to FAN and the FAN speed to High. Also, consider cleaning the air filter. Alternatively, you can defrost the coil by setting the MODE to Cool, Fan speed to high, and the Temp control to a higher temperature.
T
tararangelSep 4, 2025
Why does my Kenmore 35932 turn on and off rapidly?
- D
  David ChandlerSep 4, 2025
  If your Kenmore Air Conditioner turns on and off rapidly, it could be due to extremely hot outside temperatures. To minimize the cooling load, set the FAN SPEED on HI. Also, note that in energy saver mode, the fan turns on approximately every 3 minutes to check the room air temperature, which is normal.
M
Melinda PettySep 8, 2025
Why is my Kenmore 35932 making noise when cooling?
- A
  Adam KelleySep 8, 2025
  If your Kenmore Air Conditioner is making noise while cooling, it could be the sound of the fan hitting water from the moisture removal system, which is normal in high humidity. Close doors, windows, and registers. Alternatively, window vibration due to poor installation could be the cause. Refer to installation instructions or check with installer.