Need help?Do you have a question about the Kenwood TK-7100H and is the answer not in the manual?
General| Brand | Kenwood |
|---|---|
| Model | TK-7100H |
| Category | Transceiver |
| Language | English |
Basic steps for transmitting and receiving calls.
Programming the allowed receive frequencies for a channel.
Programming the allowed transmit frequencies for a channel.
Signalling for group communication and muting unwanted calls.
Prevents transmission on an occupied channel.
Transmitting an identification code when PTT is pressed/released.
Using an installed voice scrambler board for secure communication.
Programming the scrambler code for secure communication.
Sets transmission time limits and re-transmit intervals.
Protects transceiver use by unauthorized persons.
Protects operating frequencies and config data from unauthorized access.
Moves transceiver to Data Channel when Function Port switches logic.
Selects PTT ID type as DTMF or MSK.
Installs SmarTrunk or ST865KW4 and programs trunking groups.
Permits channel monitoring using carrier squelch.
Locks transceiver keys to prevent accidental changes.
Allows transmission using receive frequency for direct communication.
Monitors multiple programmed channels for signals.
Selects channels to add to or remove from the Scan List.
Enters Emergency Mode by pressing the Emergency key.
Activates Horn Alert output when receiving a matching DTMF string.
Changes QT/DQT Decode/Encode combination without changing frequencies.
Switches the Group Code of the SmarTrunk Board.
Selects whether to use the Scrambler Board.
Conditions required to activate the Scan function.
Conditions required for the transceiver to resume scanning.
Scan behavior when receiving calls during scanning.
Allows checking signals on Priority Channels by adding them to Scan List.
Checks for signals on Priority Channel while on a normal Channel.
The Group/Channel used for transmitting while pressing PTT during Scan.
Scans channels within a selected group or all groups.
Scans all Groups and Channels added to the Scan List.
Selects whether to execute Scan when microphone is in Off Hook position.
Functions related to encoding and transmitting DTMF signals.
Automatically transmits programmed DTMF codes (up to 9 memories).
Programs transceiver operation when ID Code matches.
Used for making individual calls and setting transceiver operation.
Programs transceiver operation based on ID Code matches.
Distinguishes ID Code and Status Code in Selective Call.
Enables making a Group call using DTMF.
Sounds the Call Alert Tone when receiving a call using DTMF.
Automatically transmits Alert or Code when ID Code matches.
Defines the type of stun action (Stun Code, TX Inhibit, TX/RX Inhibit).
Changes Horn Alert Logic when receiving a DTMF ID Code match.
Transponds after Busy Signal on current Channel is cleared.
Programs a FleetSync ID consisting of Fleet and ID numbers.
Mode for performing emergency operations, transmitting DTMF or MSK ID.
The Channel used when the transceiver enters Emergency Mode.
Sets the duration for automatic transmission in Emergency Mode.
Programs the first transmitted Emergency Code for automatic transmission.
Code to notify transceiver that the Emergency Code was received.
Code transmitted by dispatcher to exit transceiver's Emergency Mode.
Selects whether to unmute the speaker in Emergency Mode.
Allows continued Emergency operation even after turning transceiver OFF.
Unlocking the transceiver with Data Password for Clone Master use.
Assigns functions to ports for KDS-100, KGP-2A/2B, SmarTrunk, Scrambler.
Assigns input terminal to trigger Emergency mode.
Outputs scrambler codes via multiple terminals.
Terminal to select Ignition Sense function for auto ON/OFF.
Lists pin positions for the KCT-39 connector cable.
Step-by-step instructions for connecting the KCT-39 cable.
Configuring Function Port via FPU for KDS-100 operation.
Configuring Function Port via FPU for KGP-2A/2B operation.
Step-by-step guide for installing the SmarTrunk board.
Programming Function Port via FPU for SmarTrunk operation.
Instructions for installing the Scrambler board and removing resistors.
Programming Function Port via FPU for Scrambler operation.
Enables Ignition Sense via FPU and removes R71.
Using Ignition Sense with KDS-100/KGP-2A/2B to disable it.
How Data Password protects programming data.
Instructions for modifying and connecting the KCT-31 cable to the transceiver.
To Next Page
