Kessel Aqualift F Basic User Manual (English)

Other manuals for Kessel Aqualift F Basic

Instructions For Installation, Operation And Maintenance31 pages

Installation And Operating Instructions112 pages

Questions and Answers:

V
Vickie MendozaAug 14, 2025
What to do if my Kessel Aqualift F Basic is not running?
- N
  Nicole RyanAug 14, 2025
  If your Kessel Water Pump isn't running, it could be due to several reasons: * There might be no mains voltage available, in which case you should check the mains voltage. * The main power circuit breaker might have tripped; try switching it on again. * A damaged connection cable could be the issue; this should be repaired only by qualified electricians or service partners. * The pump may have overheated; it will switch back on automatically once the temperature drops. * A defective float switch can also cause this problem, in which case you should contact Customer Services.
S
Sarah HinesAug 17, 2025
Why is my Kessel Aqualift F Basic performance reduced?
- C
  Carrie JonesAug 17, 2025
  Reduced performance in your Kessel Water Pump can stem from a few causes: * The intake cage might be blocked, requiring you to clean the pump. * A blocked ventilation pipe can also reduce performance; clean the ventilation opening. * Worn components such as the spiral housing or the multi-vane impeller can also lead to reduced performance. Consider replacing the spiral housing or the multi-vane impeller.
K
Karen WoodsAug 20, 2025
How to fix a battery fault in my Kessel Plumbing Product?
- M
  Michelle ComptonAug 21, 2025
  To fix a battery fault in your Kessel Plumbing Product, check the battery connection and replace the battery if necessary. The fault may be due to a missing, faulty, or low voltage battery.
A
Amber GarzaAug 25, 2025
Why does my Kessel Plumbing Product have a max run time issue?
- K
  kimberlyreedAug 25, 2025
  A max run time issue in your Kessel Plumbing Product can occur if the pump is running too long per pumping process or if the ventilation is not working. Check the design and clean ventilation bores. You may need to adjust the run-on time using the potentiometer in the control unit, setting a shorter duration.
J
Jenny SmithAug 27, 2025
What causes the start-up cycle limit in my Kessel Plumbing Product?
- K
  khesterAug 27, 2025
  The start-up cycle limit in your Kessel Plumbing Product may be triggered if the pump starts up too often at short intervals or if the backwater preventer is faulty. Check the design and check and replace the backwater preventer if necessary.
J
jguerreroAug 30, 2025
Why is my Kessel Aqualift F Basic Water Pump not running?
- C
  Chad GarciaAug 30, 2025
  Your Kessel Water Pump might not be running due to several reasons: there could be no mains voltage, the main power circuit breaker may have tripped, the connection cable might be damaged, the float switch could be defective, or the pump may be overheating. Check the mains voltage and switch the circuit breaker on again. If the connection cable is damaged, it should only be repaired by qualified electricians/service partners. If the float switch is defective, contact Customer Services. If overheating is the issue, the submersible pump will automatically switch back on when the temperature drops.
A
Andrea SandersSep 2, 2025
What to do if my Kessel Aqualift F Basic Water Pump has reduced performance?
- N
  Nicholas PetersonSep 2, 2025
  If your Kessel Water Pump's performance is reduced, it could be due to a blocked intake cage, a worn spiral housing, a worn multi-vane impeller, or a blocked ventilation pipe. Clean the pump, replace the spiral housing or the multi-vane impeller, and clean the ventilation opening to resolve the issue.
G
greenglennSep 6, 2025
How to fix a blocked multi-vane impeller in Kessel Aqualift F Basic?
- E
  ernest63Sep 6, 2025
  A blocked multi-vane impeller in your Kessel Water Pump is likely due to soiling or solids lodged between the impeller and the spiral housing. To fix this, clean the pump.
C
Charlotte KimSep 9, 2025
What to do if Kessel Aqualift F Basic Water Pump displays a level error?
- J
  Jennifer GentrySep 9, 2025
  If your Kessel Water Pump displays a level error, it is possible that the float switch is blocked. You should carry out maintenance.

Kessel Aqualift F Basic Specifications

General

Number of inlets	3
Operating voltage	230 V
Mains frequency	50 Hz
Protection class	IP 68
Cable Length	10 m
Application	Wastewater without sewage
Inlet nominal size	DN 100
Max. pumping distance	10 m
Delivery rate	8 m³/h
Max Flow Rate	8 m³/h