Keysight N5741A - Supplemental Characteristics

Specifications Appendix A
Series N5700 User’s Guide 91
Supplemental Characteristics
Keysight Models N5741A – N5752A and N5761A – N5772A
Model
N5741A
N5761A
N5742A
N5762A
N5743A
N5763A
N5744A
N5764A
N5745A
N5765A
N5746A
N5766A
N5747A
N5767A
N5748A
N5768A
N5749A
N5769A
N5750A
N5770A
N5751A
N5771A
N5752A
N5772A
Output Response Time: (to settle to within ±1.0% of the rated output, with a resistive load)
Up, full load
0.08s
0.08s
0.08s
0.08s
0.08s
0.08s
0.08s
0.15s
0.15s
0.15s
0.15s
0.25s
Down, full load
0.05s
0.05s
0.05s
0.05s
0.08s
0.08s
0.08s
0.15s
0.15s
0.15s
0.15s
0.30s
Down, no load
0.5s
0.6s
0.7s
0.8s
0.9s
1.0s
1.1s
1.2s
1.5s
2.0s
3.0s
4s
Command Response Time: (add this to the output response time to obtain the total programming time)
55 ms
Remote Sense Compensation:
Volts/load lead
1V
1V
1V
1V
1.5V
2V
3V
4V
5V
5V
5V
5V
Over-voltage Protection:
Range
0.5-7.5V 0.5-10V 1-15V 1-24V 2-36V 2-44V 5-66V 5-88V 5-110V 5-165v 5-330V 5-660V
Accuracy
0.06V
0.08V
0.125V
0.20V
0.30V
0.40V
0.60V
0.80V
1V
1.5V
3V
6V
Output Ripple and Noise: (From 5Hz-1MHz, at 10% to 100% of output voltage at full load (for 6V units from 33% to 100% of output voltage)
CC rms 750W
200mA
180mA
120mA
76mA
63mA
48mA
38mA
29mA
23mA
18mA
13mA
8mA
CC rms 1500W
360mA
330mA
240mA
152mA
125mA
95mA
75mA
57mA
45mA
35mA
25mA
12mA
Programming Resolution:
Measurement Resolution:
Voltage
0.72mV
0.96mV
1.5mV
2.4mV
3.6mV
4.8mV
7.2mV
9.6mV
12mV
18mV
36mV
72mV
Current 750W
12mA
10.8mA
7.2mA
4.56mA
3mA
2.3mA
1.5mA
1.14mA
0.9mA
0.6mA
0.3mA
0.156mA
Current 1500W
21.6mA
19.8mA
14.4mA
9.12mA
6mA
4.6mA
3mA
2.28mA
1.8mA
1.2mA
0.6mA
0.312mA
Front Panel Display Accuracy: (4 digits; +% of rated output;
±
1 count)
Voltage
30mV
40mV
62.5mV
100mV
150mV
200mV
300mV
400mV
500mV
750mV
1.5 V
3 V
Current 750W
500mA
450mA
300mA
190mA
125mA
95mA
62.5mA
47.5mA
37.5mA
25mA
12.5mA
6.5mA
Current 1500W
900mA
825mA
600mA
380mA
250mA
190mA
125mA
95mV
75mA
50mA
25m
13mA
Temperature Drift: (over 8 hours, after a 30 minute warm-up, with constant line, load, and temperature)
Voltage
3mV
4mV
6.25mV
10mV
15mV
20mV
30mV
40mV
50mV
75mV
150mV
300mV
Current 750W
50mA
45mA
30mA
19mA
12.5mA
9.5mA
6.25mA
4.75mA
3.75mA
2.5mA
1.25mA
6.5mA
Current 1500W
90mA
82.5mA
60mA
38mA
25mA
19mA
12.5mA
9.5mA
7.5mA
5mA
2.5mA
1.3mA
Temperature Coefficient: (after a 30 minute warm-up)
Voltage and Current
100PPM/°C from rated output voltage or current
Analog Programming and Monitoring:
Vout voltage
0 - 100%, 0-5V/10V, user selectable, Accuracy & linearity = +/-0.5% of rated Vout
Iout voltage
0 - 100%, 0-5V/10V, user selectable, Accuracy & linearity = +/-1% of rated Iout
Vout resistance
0 - 100%, 0-5kΩ/10kΩ, user selectable, Accuracy & linearity = +/-1% of rated Vout
Iout resistance
0 - 100%, 0-5kΩ/10kΩ, user selectable, Accuracy & linearity = +/-1.5% of rated Iout
Iout monitor
0-5V/10V, user selectable, Accuracy = 1%
Vout monitor
0-5V/10V, user selectable, Accuracy = 1%
On/Off control
Electrical voltage; 0-6V/2-15V or dry contact, user selectable logic
PS OK signal
5V = OK; 0V = FAIL; 500Ω series resistance
CV/CC signal
CV = TTL high (4-5V) source current 10mA; CC = TTL high (4-5V) sink current 10mA
Enable/Disable
Dry contact. Open=Off, Short=On. Maximum voltage at terminal= 6V.