Spectra Essential EN 12/12
Guidance and manufacturer’s declaration
Guidance and manufacturer’s declaration - Electromagnetic immunity
The device KINETEC
®
SPECTRA Essential is intended for use in the electromagnetic environment specified below. The customer or the user
of the device KINETEC
®
SPECTRA Essential should ensure that it is used in such an environment.
Immunity test
Test level according to
EIC 60601
Compliance
level
Electromagnetic environment –
guidance
Mobile and portable RF communication devices should not
be used closer to any part of the device KINETEC
®
SPECTRA
Essential machine, including its cables, than the
recommended separation distance, calculated based on the
equation applicable to the emitter's frequency.
Recommended separation distance
Conducted RF interference
IEC 61000-4-6
3 Veff
from 150 kHz to 80 MHz
3 V
d = 1.2
P
Radiated RF interference
IEC 61000-4-3
3 V/m
from 80 MHz to 2.5 GHz
3 V/m
d = 1.2
P from 80 MHz to 800 MHz
d = 2.3
P from 800 MHz to 2.5 GHz
where P is the emitter's maximum output power characteristic
in watts (W), according to the emitter's manufacturer, and d is
the recommended separation distance in metres (m).
The field intensities of fixed RF emitters, determined by an on-
site electromagnetic investigation
a
, should be below the
compliance level in each frequency range
b
.
There may be interference near appliances bearing the
following symbol:
NOTE 1 At 80 and 800 MHz, the highest frequency range is applicable.
NOTE 2 These directives cannot be applied in every situation. Electromagnetic propagation is affected by absorption and reflection
by structures, objects and people.
a
The field intensity of fixed emitters such as base stations for radio-telephones (cellular/cordless) and land mobile radios, amateur
radio, AM/FM radio broadcasts and TV broadcasts cannot be predicted exactly in theory. To evaluate the electromagnetic
environment due to fixed RF emitters, an on-site electromagnetic investigation should be considered. If the field intensity measured
where the device KINETEC
®
SPECTRA Essential machine is used exceeds the aforementioned applicable RF compliance level, the
device KINETEC
®
SPECTRA Essential machine should be monitored to check that it is working normally. If abnormal results are
observed, additional measures may be necessary, such as reorienting or repositioning the device KINETEC
®
SPECTRA Essential.
b
Over the frequency range 150 kHz to 80MHz, field intensities should be less than 3V/m.
Recommended separation distances between mobile and portable RF communication devices and the device KINETEC
®
SPECTRA
Essential machine
The device KINETEC
®
SPECTRA Essential machine is designed to be used in an electromagnetic environment in which radiated RF
interference is controlled. The customer or user of the device KINETEC
®
SPECTRA Essential machine can help prevent electromagnetic
interference by maintaining a minimum distance between mobile and portable RF communication devices (emitters) and the device
KINETEC
®
SPECTRA Essential machine, as recommended below, according to the communication device's maximum output power.
Maximum assigned output power
for the emitter
W
Separation distance according to the emitter's frequency
m
from 150 kHz to 80 MHz
d = 1.2
P
80 MHz to 800 MHz
d = 1.2 P
from 800 MHz to 2.5 GHz
d = 2.3 P
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For emitters whose assigned maximum emitted power is not given above, the recommended separation distance d in metres (m) can
be estimated using the equation applicable to the emitter frequency, where P is the emitter's maximum emission power characteristic in
watts (W), according to the latter's manufacturer.
NOTE 1 At 80 and 800 MHz, the separation distance for the highest frequency range is applicable.
NOTE 2 These directives cannot be applied in every situation. Electromagnetic propagation is affected by absorption and
reflection by structures, objects and people.
To Next Page
Loading...
