Kirisun PT8000 User Manual (English)

Other manuals for Kirisun PT8000

Questions and Answers:

F
floresjanetSep 9, 2025
What to do if my Kirisun Transceiver fails to power on?
- P
  Peter MurphySep 9, 2025
  If your Kirisun Transceiver fails to power on, consider the following: * Ensure the power cable is securely connected to both the accumulator and the host. * Check the power cable's protective tube for burnout and replace if necessary. * Inspect the power button for poor contact; replace the silica gel button or PCB button if needed. * Verify the rechargeable battery has power; recharge or replace it if depleted. * If none of the above steps work, the CPU might be broken, consider replacing the IC.
M
Michael HallAug 23, 2025
What to do if my Kirisun PT8000 Radio has no receiving signal?
- R
  Robert CampbellAug 23, 2025
  If your Kirisun Radio isn't receiving a signal, consider the following: * Check the antenna connection. Ensure the antenna head is securely fastened. * The high-frequency amplifying tube Q18 might be broken and needs replacement. * The squelch level could be set too high. Reset the squelch level. * The mixed tube Q19 may be damaged and require replacement. * The FM IC6 might be broken, requiring IC replacement.
T
Timothy WilsonAug 25, 2025
How to fix a power on failure on a Kirisun Radio?
- C
  clarkrebeccaAug 25, 2025
  If your Kirisun Radio fails to power on, here are several things to check: 1. Ensure the power cable is securely connected to both the accumulator and the host. 2. Inspect the power cable's protective tube for burnout; replace it if necessary. 3. Examine the power button for poor contact; consider replacing the silica gel or PCB button. 4. Verify the rechargeable battery has sufficient power; recharge or replace it if needed. 5. The CPU might be broken, consider replacing the IC.
J
Janet MoraAug 27, 2025
Why does my Kirisun Radio keep beeping (phase lock loop unlocked)?
- J
  Jeremiah HollowayAug 27, 2025
  If your Kirisun Radio is beeping due to a phase lock loop unlock, it could be due to: * The channel frequency is beyond the supported range. Reset the channel data. * The crystal X1 of the phase lock loop is broken and needs replacement. * The oscillator tube is broken, you should replace it. * The IC3 of the phase lock loop is broken, you should change the IC.
F
frank77Aug 27, 2025
What to do if the green receiving indicator lights up on my Kirisun PT8000, but no sound is heard?
- S
  Suzanne HobbsAug 27, 2025
  If the green receiving indicator is lit on your Kirisun Radio but you hear no sound, it might be that the speaker is broken and needs replacement. Alternatively, the audio power amplifier IC7 could be broken, requiring IC replacement.
G
Gabriel GarnerAug 29, 2025
What to do if the red transmission indicator lights up on my Kirisun Radio, but no sound is heard?
- L
  Lisa StantonAug 29, 2025
  If the red transmission indicator lights up on your Kirisun Radio but you hear no sound, it could be due to a damaged power module IC1 with no power output, which requires module replacement. It could also be a damaged MIC, which also requires replacement.
L
Levi BowmanSep 14, 2025
Why does the red transmission indicator light up on my Kirisun Transceiver, but no sound is heard?
- L
  Levi GrantSep 14, 2025
  If the red transmission indicator lights up but no sound is heard on your Kirisun Transceiver, it could be due to: * A damaged Power module IC1 with no power output, please replace the module. * A damaged MIC, please replace it.
H
Heidi WilliamsSep 12, 2025
Why does my Kirisun Transceiver have no talkback?
- R
  Richard CarpenterSep 12, 2025
  If your Kirisun Transceiver has no talkback, it might be due to several reasons: * The selected frequency might be incorrect. Try reselecting the channel with the correct frequency. * The CTCSS/DCS code might not match. Reset the CTCSS/DCS code to ensure it is the same as the receiving unit. * You might be out of the effective communication range.
M
Matthew CombsSep 8, 2025
Why does my Kirisun Radio beep with PLL unlocked?
- D
  Darlene GreeneSep 8, 2025
  If your Kirisun Radio is beeping and showing a PLL unlocked error, it could be due to several reasons. First, the channel frequency might be beyond the limit; reset the channel data. Second, the PLL crystal oscillator X1 may be broken, requiring replacement. Third, the oscillator transistor might be broken, also requiring replacement. Finally, the PLL IC3 could be broken, necessitating its replacement.
J
jacquelinekhanSep 4, 2025
What to do if Kirisun PT8000 LED lights red but no voice is heard?
- S
  Sean FullerSep 5, 2025
  If the LED on your Kirisun Radio lights red during transmission, but no voice is heard by the recipient, it could be due to a broken power module IC1, meaning there is no power output. In this case, replace the module. Alternatively, the microphone itself might be broken, necessitating its replacement.