Konica Minolta cm-5 User Manual (English)

Other manuals for Konica Minolta cm-5

Instruction Manual174 pages

Brochure4 pages

Questions and Answers:

D
Derrick GonzalezAug 13, 2025
What to do if Konica Minolta Test Equipment shows abnormal measurement result?
- R
  Richard HollandAug 13, 2025
  If you are getting abnormal measurement results with your Konica Minolta Test Equipment, ensure the specimen is securely placed to prevent light leakage. Also, verify that you're using the correct calibration data, especially for user calibration or Petri Dish measurements, using the optional software. Confirm the calibration plate matches the input data before performing white calibration. It is also important to ensure that zero calibration was performed correctly, using the optional Zero Calibration Box.
L
Lynn AlvarezAug 17, 2025
Why won't my Konica Minolta Test Equipment data save or read from USB memory?
- M
  margaretsnyderAug 17, 2025
  If your Konica Minolta Test Equipment is unable to save files to or read files from a USB memory, ensure the USB memory is properly and securely connected to the instrument's USB connection terminal. If the problem persists, try turning the instrument OFF and then ON again before reconnecting the USB memory.
Q
qleeAug 20, 2025
Why is my Konica Minolta Test Equipment not connecting to the computer?
- L
  lisa28Aug 20, 2025
  If your Konica Minolta Test Equipment is not connecting to the computer, ensure that you are using the USB cable supplied with the instrument and that it is correctly connected between the instrument’s USB connecting terminal and the computer’s USB port.
A
Adam MannAug 25, 2025
Why does measurement data disappear on my Konica Minolta Test Equipment?
- F
  Frank ClarkAug 25, 2025
  If measurement data or settings are not held in memory and disappear immediately on your Konica Minolta Test Equipment, the instrument’s backup battery may be low, especially after purchase or prolonged non-use. Turn the instrument ON to charge the backup battery; it can be fully charged in 72 hours. If the issue persists after charging, the battery may need replacement by a KONICA MINOLTA-authorized service facility.
J
Joan HopkinsAug 28, 2025
What to do if Konica Minolta Test Equipment measurement results fluctuate?
- T
  Taylor EvansAug 28, 2025
  If the measurement results from your Konica Minolta Test Equipment are fluctuating, make sure that both the instrument and the specimen remain stationary during measurement. Avoid any movement during the process.
J
Juan LambSep 1, 2025
What to do if measuring button is not effective on Konica Minolta Test Equipment?
- P
  proctorsarahSep 1, 2025
  If the measuring button on your Konica Minolta Test Equipment is not working, first check if a measurement is currently in progress. If so, wait until it is complete before pressing the button again. Also, ensure that a screen where measurement is possible (e.g., Calibration, Target, or Sample screen) is displayed, as the measuring button must be pressed while one of these screens is active.
S
Sydney FloresSep 5, 2025
Why is my Konica Minolta Test Equipment not printing?
- M
  Mary OsborneSep 5, 2025
  If your Konica Minolta Test Equipment is not printing, verify that the printer cable is correctly connected. Ensure the RS-232C connector of the instrument is connected to the printer's connector using either the optional connecting cable or a cable conforming to the requirements shown in the connection diagram.
C
christiankimberlySep 9, 2025
How to fix a blank LCD screen on Konica Minolta Test Equipment?
- J
  Jeffrey GreenSep 9, 2025
  To fix a blank LCD screen on your Konica Minolta Test Equipment, connect the AC adapter.

Konica Minolta cm-5 Specifications

General

Light Source	Pulsed Xenon Lamp
Measurement Range	0 to 200% reflectance
Wavelength Range	360 nm to 740 nm
Wavelength Interval	10 nm
Observer	2° and 10°
Illuminant	A, C, D50, D65, F2, F6, F7, F8, F10, F11, F12
Spectral separation device	Diffraction grating
Type	Spectrophotometer
Geometry	d/8° (diffuse illumination, 8° viewing)
Measurement Area	MAV: ø 8 mm
Repeatability	Spectral reflectance: Standard deviation within 0.1%
Inter-instrument Agreement	Within ΔE*ab 0.15
Colorimetric data	Spectral reflectance
Display	Color LCD
Interface	USB 2.0
Power	AC 100-240V, 50/60Hz
Operating Temperature	13°C to 33°C
Operating Humidity	Relative humidity 80% or less (no condensation)
Storage temperature/humidity range	0 to 40°C, relative humidity 80% or less (no condensation)
Port Size	ø 30 mm
Measurement Accuracy	Within ΔE*ab 0.15