What does 'Line disconnected because there is no appropriate confidential user box while automatic user box generation is inhibited' mean on Konica Minolta FK-502 All in One Printer?
This issue arises because the confidential box number received from the remote station may be incorrect.
What to do if my Konica Minolta All in One Printer displays a device error (GA), what should I do?
If your Konica Minolta All in One Printer displays a 'Device error (GA)', first turn the power off and then on again. If the problem persists, the fax board may be defective and require replacement.
What to do if my Konica Minolta FK-502 displays a device error (DRAM), what should I do?
If your Konica Minolta All in One Printer displays a 'Device error (DRAM)', first turn the power off and then on again. If the problem persists, the fax board may be defective and require replacement.
What to do if my Konica Minolta FK-502 displays a device error (GA LOCAL SRAM), what should I do?
If your Konica Minolta All in One Printer displays a 'Device error (GA LOCAL SRAM)', first turn the power off and then on again. If the problem persists, the fax board may be defective and require replacement.
What to do if my Konica Minolta FK-502 displays a soft error (Fax board side)?
If your Konica Minolta All in One Printer shows a 'Soft error (Fax board side)', try turning the power off and then on again.
What to do if my Konica Minolta FK-502 exceeds the number of pages specified for reception?
Ask the sender to resend the document with a reduced number of pages.
What to do if my Konica Minolta FK-502 All in One Printer experiences a timeout error due to non-response from codec control during suspension process?
If you encounter this timeout error, turn the power off and then on again.
What to do if my Konica Minolta All in One Printer shows SMTP reception error?
If the SMTP reception doesn't start within 60 minutes after connection for an incoming call, this error might occur. Ask the sender to resend the message.
What does 'Unsatisfactory conditions for receive polling tx request' mean for my Konica Minolta FK-502?
This indicates that the bulletin board original may not be set. Bulletin board TX is enabled only when the bulletin board transmission original is registered.
What does 'Calling by polling reception, but a remote station does not have polling documents' mean for Konica Minolta All in One Printer?
This indicates that the polling original may not be set on the remote station.
Provides an overview of the device, including basic and general specifications, scanning, recording, line connection, and operation panel details.
Details the fundamental specifications of the device, covering applicable lines, protocols, data rates, coding, and resolution.
Details various functional specifications of the fax machine, including dial functions, transmission capabilities, polling, and line seizure modes.
Covers specifications for Internet Fax and IP Address Fax, including image memory capacity, stored pages, scanning density, and transmission modes.
Details the communication control aspects, including protocols, modem fallback sequences, and V8/V34 sequences.
Explains communication protocols, including FIF bits of DIS, DTC, and DCS, and various data configuration lists.
Describes the TEL/FAX switching function, including its operation and parameters for automatic switching between telephone and FAX.
Explains key functions of the fax system, including F-code functions, transmission, reception, and management features.
Details the F-code functions for confidential transmission, bulletin board polling, and relay transmission, including signals and box specifications.
Covers transmission functions, including original scan modes, default settings, and frame erasure options.
Provides step-by-step procedures for replacing various components and boards across different bizhub models.
Guides users on how to use the Adjustment/Setting section, including advance checks and precautions for service jobs.
Details the Service Operation Mode, including machine settings, counter, list output, and state confirmation menus.
Provides an overview of the Service Mode, its menu tree, and procedures for accessing various settings like modem, system, and communication.
Details how to set various function parameters, including modem/NCU, system, communication, fax file format, list output, and initialization.
Details the Test Mode, including its outline, menu tree, and procedures for signal sending, receiving, and NCU tests.
Provides guidance on troubleshooting various issues, including error codes, diagnostic codes, and specific error codes for transmission and reception.
Lists various error codes related to the FAX board and driver, detailing their contents and corrective actions.
Details error codes specific to network fax operations, categorizing them into transmission and reception system errors with corrective actions.
Contains supplementary information, including address parameter lists, wiring diagrams, and function differences by model.
General| Brand | Konica Minolta |
|---|---|
| Model | FK-502 |
| Category | All in One Printer |
| Language | English |
To Next Page