A
Amy SanchezSep 7, 2025
Why Konica Minolta BIZHUB 164 All in One Printer cannot select items in the printer driver?
- DDarryl RamirezSep 7, 2025
Some functions cannot be combined. Grayed out items cannot be configured.
To Next PageTo Next PageWhy Konica Minolta BIZHUB 164 All in One Printer cannot select items in the printer driver?
Some functions cannot be combined. Grayed out items cannot be configured.
What to do if Konica Minolta All in One Printer shows "Printer is not connected" or "Print Error"?
First, check the specified printer name, as the printer driver may not be supported by the printer controller. Next, ensure the USB cable is correctly connected. Also, check the Display of the machine for any error messages. Finally, perform a test printing to check whether printing is possible, as memory may be insufficient.
Why copying does not start on Konica Minolta All in One Printer?
There are several possible reasons: 1. The Fusing Unit Top Cover/1st Side Cover of the machine might be open. Ensure it is securely closed. 2. The machine may still be warming up. It takes about 30 seconds to warm up after being turned on, so wait until it finishes. 3. An error message or icon may be displayed. Follow the instructions in any messages that appear on the Display.
Why print processing on computer finished, but printing does not start on Konica Minolta BIZHUB 164 All in One Printer?
This issue can occur for several reasons. First, verify the specified printer name, as the printer driver may not be supported. Second, check that the USB cable is correctly connected. Also, examine the Display of the machine for any error messages. Another possibility is that unprocessed jobs may remain and be waiting to be processed, so wait until the current job is done. Finally, insufficient computer memory can cause this, so perform a test printing.
What to do if Konica Minolta BIZHUB 164 prints too light?
The density might be set too light. Press the ) key (darker) in the density setting to select the desired density. Alternatively, the paper might be damp. If so, replace it with new paper.
What to do if Konica Minolta All in One Printer prints too dark?
The density might be set too dark. Press the * key (lighter) in the density setting to select the desired density. Another cause may be that the original was not pressed close enough against the Original Glass. Position the original so that it is pressed closely against the Original Glass.
Why images are not printed properly on Konica Minolta BIZHUB 164?
Insufficient memory of the computer may be the reason. Simplify the images to reduce the data size.
What does "conflict" message mean on Konica Minolta BIZHUB 164 All in One Printer?
This message indicates that you are trying to configure functions that cannot be combined. Check carefully the functions you have specified, then specify functions that can be combined.
Why nothing appears on Konica Minolta All in One Printer display?
If the indicator on the Start key is lit up in green, the machine has entered Sleep mode. Press any key on the Control Panel to cancel Sleep mode.
Why Konica Minolta BIZHUB 164 All in One Printer prints curled pages?
If you are using paper that curls easily, such as recycled paper, remove it from the paper tray, turn it over, and load it again. You can also try replacing the paper with new, dry paper.
General| Print Technology | Laser |
|---|---|
| Print Speed | 16 ppm |
| Print Resolution | 600 x 600 dpi |
| Copy Speed | 16 cpm |
| Copy Resolution | 600 x 600 dpi |
| Scan Resolution | 600 x 600 dpi |
| Paper Capacity | 250 sheets |
| Interface | USB 2.0 |
| Warm-up Time | 29 seconds |
| Paper Input Capacity | 250 sheets |
| Memory | 32 MB |
| Type | Monochrome |
| Maximum Paper Size | A3 |
| Duplex Printing | Manual |
| Network Connectivity | No |
| USB Connectivity | Yes |
| Paper Size | A5 |
| Fax Resolution | Not applicable |
Important safety precautions, warning symbols, and guidelines for safe operation.
Precautions for power source, operating environment, storage of copies, and transportation.
Procedure for powering the machine on and off, including sleep mode.
Instructions for basic operations such as loading paper and placing originals.
Information and requirements for installing the printer/scanner driver.
Step-by-step guide for installing drivers using the Plug and Play method.
How to send print jobs from applications, cancel jobs, and manage sleep mode.
Information and procedures for using the TWAIN scanner driver.
Procedure for checking and replacing the toner bottle.
Procedure to follow when a machine trouble message appears.
A guide to common problems and their solutions.
Step-by-step instructions for clearing paper jams in various sections.
