What does "Read Data Error" mean on Konica Minolta All in One Printer?
If a message saying "Read Data Error" appears on the computer screen when using the Konica Minolta All in One Printer, turn off the machine, then check that the USB cable is correctly connected. After checking the USB cable, turn on the machine again.
What to do if Konica Minolta All in One Printer shows "Printer is not connected"?
If you see a "Printer is not connected" or "Print Error" message on your computer screen when using the Konica Minolta All in One Printer, check the specified printer name. Also, verify that the USB cable is correctly connected. An error may have occurred on the machine, so check the display. Insufficient memory may also be the cause, so perform a test printing to see if printing is possible.
What to do if Konica Minolta All in One Printer copying does not start?
If copying does not start on your Konica Minolta All in One Printer, it could be due to several reasons. First, ensure that the Fusing Unit Top Cover/1st Side Cover of the machine is securely closed. Also, the machine may still be warming up after being turned on (it takes about 30 seconds). Finally, check the display for any error messages or icons and follow the provided instructions.
What to do if Konica Minolta All in One Printer printed output is too light?
If the printed output from your Konica Minolta All in One Printer is too light, it may be because the density is set too light. Press the ) key (darker) in the density setting to select the desired density. The paper may also be damp, so try replacing it with new paper.
What to do if Konica Minolta All in One Printer printed output is too dark?
If the printed output from your Konica Minolta All in One Printer is too dark, it could be because the density is set to the darker side. Press the * key (lighter) in the density setting to select the desired density. Alternatively, the original may not have been pressed closely enough against the Original Glass. Ensure the original is positioned correctly.
What to do if Konica Minolta All in One Printer image is partially obscured?
If the image from your Konica Minolta All in One Printer is partially obscured or blurry, it might be due to damp paper. Replace it with new paper. Another cause could be that the original was not pressed closely enough against the Original Glass; reposition the original to ensure it is pressed closely.
What does "Machine error" mean on Konica Minolta All in One Printer?
If a message saying "Machine error" appears on the computer screen when using the Konica Minolta All in One Printer, there may be a problem with the transmission of commands between the TWAIN driver and the machine. Check the USB cable connected to the machine.
What does "Scanner not ready" mean on Konica Minolta All in One Printer?
If a message saying "Scanner not ready" appears on the computer screen when using the Konica Minolta All in One Printer, turn off the machine, then check that the USB cable is correctly connected. After checking the USB cable, turn on the machine again.
Why Konica Minolta All in One Printer printed page is curled?
If the printed page from your Konica Minolta All in One Printer is curled, it might be due to using paper that curls easily, such as recycled paper. Remove the paper from the paper tray, turn it over, then load it again. Also, the paper might be damp, replace with new dry paper.
What to do if Konica Minolta All in One Printer displays nothing?
If nothing appears on the display of your Konica Minolta All in One Printer, and the indicator on the Start key is lit up in green, the machine has entered Sleep mode. Press any key in the Control Panel to cancel the Sleep mode.
General| Print Speed | 18 ppm |
|---|---|
| Print Resolution | 600 x 600 dpi |
| Copy Speed | 18 cpm |
| Copy Resolution | 600 x 600 dpi |
| Scan Resolution | 600 x 600 dpi |
| Paper Capacity | 250 sheets |
| Printing Technology | Laser |
| First Print Out Time | 8 seconds |
| First Copy Out Time | 8 seconds |
| Paper Output Capacity | 100 sheets |
| Memory | 32 MB |
| Type | Monochrome |
| Max Paper Size | A3 |
| Duplex Printing | Manual |
| Network Connectivity | No |
| Zoom Range | 50% to 200% |
| Paper Size | A5 to A3 |
Essential instructions for safe operation and maintenance to prevent injury or damage.
Guidelines for power source, environment, and handling during operation.
Detailed description of the control panel buttons and their functions.
Procedures for turning the machine on, off, and managing sleep mode.
Detailed explanation of each button on the control panel and its function.
Detailed settings for specific copy functions like ID Copy, Erase, and Book Separation.
Step-by-step guide for installing drivers using the Plug and Play method.
Instructions for installing drivers using the included setup program.
Configuration options for the GDI printer driver.
Configuration options for the XPS printer driver.
Procedures for checking toner status and replacing the toner bottle.
Actions to take when specific machine trouble messages appear.
Table of common problems, causes, and their remedies.
Step-by-step instructions for clearing paper jams in different sections.
To Next Page