Konica Minolta BIZHUB 164 User Manual (English)

Other manuals for Konica Minolta BIZHUB 164

Questions and Answers:

K
Karen GarciaAug 31, 2025
How to fix dark specks or streaks on Konica Minolta BIZHUB 164 All in One Printer printed output?
- W
  williamsfranklinAug 31, 2025
  This issue can be caused by a dirty Original Glass, so wipe it with a soft, dry cloth. Alternatively, the Original Pad might be dirty; clean it with a soft cloth dampened with a mild detergent. If the original was printed on highly translucent material, place a blank sheet of paper on top of the original. If a thin 2-sided original is being copied, the print on the back side may be reproduced on the front side; adjust the density level by pressing the * key (lighter).
V
Vickie CookAug 30, 2025
What to do if Konica Minolta BIZHUB 164 All in One Printer prints partially obscured or blurry images?
- L
  Lori RamirezAug 30, 2025
  The paper might be damp, so replace it with new paper. Also, ensure the original is pressed closely against the Original Glass.
C
Christopher SkinnerAug 29, 2025
What to do if Konica Minolta All in One Printer prints too dark?
- H
  Hailey RivasAug 29, 2025
  The density might be set too dark. Press the * key (lighter) in the density setting to select the desired density. Another cause may be that the original was not pressed close enough against the Original Glass. Position the original so that it is pressed closely against the Original Glass.
B
bryantranAug 27, 2025
What to do if Konica Minolta BIZHUB 164 prints too light?
- J
  Jason HaynesAug 27, 2025
  The density might be set too light. Press the ) key (darker) in the density setting to select the desired density. Alternatively, the paper might be damp. If so, replace it with new paper.
J
joshua64Aug 26, 2025
Why print processing on computer finished, but printing does not start on Konica Minolta BIZHUB 164 All in One Printer?
- C
  Cathy TaylorAug 26, 2025
  This issue can occur for several reasons. First, verify the specified printer name, as the printer driver may not be supported. Second, check that the USB cable is correctly connected. Also, examine the Display of the machine for any error messages. Another possibility is that unprocessed jobs may remain and be waiting to be processed, so wait until the current job is done. Finally, insufficient computer memory can cause this, so perform a test printing.
J
Jean WolfAug 25, 2025
Why copying does not start on Konica Minolta All in One Printer?
- K
  Kimberly WhiteAug 26, 2025
  There are several possible reasons: 1. The Fusing Unit Top Cover/1st Side Cover of the machine might be open. Ensure it is securely closed. 2. The machine may still be warming up. It takes about 30 seconds to warm up after being turned on, so wait until it finishes. 3. An error message or icon may be displayed. Follow the instructions in any messages that appear on the Display.
C
Christopher CantuAug 23, 2025
What to do if Konica Minolta All in One Printer shows "Printer is not connected" or "Print Error"?
- K
  Kendra MoraAug 25, 2025
  First, check the specified printer name, as the printer driver may not be supported by the printer controller. Next, ensure the USB cable is correctly connected. Also, check the Display of the machine for any error messages. Finally, perform a test printing to check whether printing is possible, as memory may be insufficient.

Konica Minolta BIZHUB 164 Specifications

General

Print Technology	Laser
Print Speed	16 ppm
Print Resolution	600 x 600 dpi
Copy Speed	16 cpm
Copy Resolution	600 x 600 dpi
Scan Resolution	600 x 600 dpi
Paper Capacity	250 sheets
Interface	USB 2.0
Warm-up Time	29 seconds
Paper Input Capacity	250 sheets
Memory	32 MB
Type	Monochrome
Maximum Paper Size	A3
Duplex Printing	Manual
Network Connectivity	No
USB Connectivity	Yes
Paper Size	A5
Fax Resolution	Not applicable