What to do if Konica Minolta Magicolor 1650EN power is not on?
If your Konica Minolta Printer isn't powering on, start by checking the power cord to ensure it's correctly plugged into the outlet. Test the outlet with another electrical appliance to confirm it's working. Make sure the power switch is in the 'I' (on) position. Finally, verify that the power source matches the printer's specifications.
Why does my Konica Minolta Magicolor 1650EN reset or turn off frequently?
If your Konica Minolta Printer frequently resets or turns off, ensure the power cord is correctly plugged into the outlet. Turn off the printer, confirm the connection, and then turn the printer back on. If the issue continues, contact Technical Support with the error information.
What to do if my Konica Minolta Magicolor 1650EN power is not on?
If your Konica Minolta printer isn't powering on, try these steps: 1. Ensure the power cord is correctly plugged into the outlet. Turn off the printer before checking, then turn it back on. 2. Test the outlet with another device to confirm it's working. 3. Make sure the power switch is in the 'on' (I) position; try toggling it off (O) and then back on (I). 4. Verify the printer is connected to a power source matching its specifications.
Why is my Konica Minolta Magicolor 1650EN misfeeding?
If your Konica Minolta Printer is misfeeding media, it could be due to several reasons. First, ensure the media is correctly positioned in the tray. If the tray is overloaded, remove the excess media to the allowed amount. Also, check if the media guides are properly adjusted to the media size. Avoid using warped or wrinkled media; replace it with smooth media. High humidity can also cause misfeeding, so use dry media. Remember that special media should only be loaded in Tray 1. Ensure that label sheets and envelopes are loaded correctly, following the manufacturer's instructions and with flaps facing down, respectively. Finally, make sure you are using KONICA MINOLTA-approved media.
Why does my Konica Minolta Magicolor 1650EN take so long to print?
If printing with your Konica Minolta Printer is taking longer than expected, it could be due to a few reasons. Printing with special media types, such as thick stock, can slow down the process. Also, the printer may be in power-saving mode, which adds a delay at the start of printing. If you are using regular paper, ensure that the media type is correctly set in the driver. For very complex jobs, simply allow the printer more time to complete the task. Lastly, make sure you are using a KONICA MINOLTA toner cartridge approved for your printer.
Why is my Konica Minolta Magicolor 1650EN Printer printing blank pages?
If your Konica Minolta Printer is printing blank pages, check the toner cartridges to ensure they are not empty or defective. If a cartridge is empty, replace it. Also, verify that the media type selected in the driver matches the media loaded in the printer.
How to fix low image density on Konica Minolta Magicolor 1650EN?
If the image from your Konica Minolta Printer is too light, first try cleaning the print head window. If that doesn't help, the media might be moist, so replace it with dry media. Also, check the toner cartridge, as low toner levels can cause light images; replace the cartridge if needed.
What to do if media mis-feed message stays on Konica Minolta Magicolor 1650EN?
If the media mis-feed message persists on your Konica Minolta Printer, try opening and closing the top cover to reset the printer. Also, check the media path to ensure all misfed media has been removed.
How to resolve image defects on Konica Minolta Magicolor 1650EN?
If you're experiencing image defects with your Konica Minolta Printer, start by cleaning the print head window. Also, check the toner cartridges for any signs of leakage or damage and replace any damaged cartridges.
Why is the duplex option mis-feeding on my Konica Minolta Printer?
If the duplex option on your Konica Minolta Printer is misfeeding, ensure you are using KONICA MINOLTA-approved media. Make sure you're using only Letter/A4 plain paper and recycled paper for auto-duplexing, and that the media type is set correctly in the driver. Avoid mixing media types in Tray 1 and do not duplex envelopes, labels, thick stock, postcards, or letterheads.
Printing| print speed monochrome | up to 20 ppm |
|---|---|
| print speed colour | up to 5 ppm |
| first page out monochrome | 13 seconds |
| first page out colour | 22 seconds |
| max resolution | PhotoART 9600 (600 dpi x 600 dpi x 4 bit) |
Power| input voltage range | 220 ~ 240 V ( [+]– 10 %) |
|---|---|
| frequency | 50 ~ 60 Hz ( [+]– 3 %) |
| power consumption colour printing | 470 W or less |
| power consumption monochrome printing | 510 W or less |
| power consumption stand by | 200 W or less |
| power consumption energy save mode | 22 W or less |
Environmental| temperature | 10 ~ 35 °C |
|---|---|
| humidity | 15 ~ 85 % RH |
| noise levels operating colour | 49 dB or less |
| noise levels operating monochrome | 50 dB or less |
| noise levels stand by | 29 dB or less |
Consumables| pre-installed toner yield cyan, magenta, yellow | up to 500 pages |
|---|---|
| pre-installed toner yield black | up to 1, 000 pages |
| replacement toner yield standard cyan, magenta, yellow | up to 1, 500 pages |
| replacement toner yield high capacity cyan, magenta, yellow, black | up to 2, 500 pages |
| imaging unit black yield | up to 45, 000 pages |
| imaging unit cyan, magenta, yellow yield | up to 11, 250 pages |
Weight and Dimensions| weight | 15.1 kg |
|---|---|
| dimensions | 396 mm x 380 mm x 275 mm |
Weight and Dimensions| weight | 19.3 kg |
|---|---|
| dimensions | 396 mm x 435 mm x 337 mm |
Weight and Dimensions| weight | 22 kg |
|---|---|
| dimensions | 396 mm x 565 mm x 392 mm |
Introduces printer components and physical layout.
Details printer driver contents on CD/DVD for various OS.
Lists utilities and documentation available on CD/DVD for printer management.
Outlines hardware/software specs needed to operate the printer.
Guides on configuring default printer driver settings for Windows.
Provides steps to remove the printer driver from Windows systems.
Explains how to view current printer driver settings in Windows.
Details common buttons and tabs within Postscript and PCL printer drivers.
Instructions on how to open, use, and interpret the printer status monitor.
Introduces the printer's control panel, indicators, and keys.
Explains the indicators for toner levels in the printer's control panel.
Details settings related to paper handling, trays, and media types.
Covers settings for print quality adjustments like toner and image refresh.
Describes network and connection interface settings for the printer.
Explains how to configure printer operational defaults and security settings.
Allows changing the display language for the printer's message window.
Lists supported media types, sizes, and their specifications for printing.
Describes various media types (plain paper, thick stock, envelopes, labels) and their usage.
Details the printable margins and limitations on different media sizes.
Step-by-step instructions for loading various media types into printer trays.
General notes and information about toner cartridges and their handling.
Detailed procedure for removing and installing toner cartridges.
Instructions for using the "REMOVE ALL" mode to remove all toner cartridges.
Guide on how to replace the printer's imaging cartridge.
Steps for safely replacing the fuser unit, noting hot components.
General guidelines for printer care, cleaning, and handling precautions.
Instructions for cleaning the exterior and interior parts of the printer.
Steps to clean the media feed rollers to prevent misfeeds.
Procedure for cleaning the print head window for optimal print quality.
Specific instructions for cleaning media feed rollers in Tray 2.
Instructions for cleaning media feed rollers when using an attachment.
Guide on cleaning the rollers within the duplex unit.
Overview of troubleshooting and how to resolve common printer issues.
Steps to print a configuration page to verify printer settings.
Advice on avoiding paper jams and ensuring proper media handling.
Illustrates the printer's media path to help locate misfeeds.
Procedures for clearing paper jams from different printer locations.
Common symptoms, causes, and solutions for media misfeed issues.
Troubleshooting steps for issues like power, connectivity, and job errors.
Solutions for common printing quality issues like blank spots or poor density.
Explains status, error, and service messages displayed on the control panel.
Introduces accessories like Tray 2 and Duplex Option, and installation prerequisites.
Instructions for installing the optional 500-sheet Tray 2.
Details on installing the duplex option for automatic double-sided printing.
Provides detailed technical data and specifications for the printer.
Lists the expected lifespan of printer consumables.
Information on the printer's compliance with environmental standards like ENERGY STAR.
To Next Page