153
Appendices
Flt KT +/+ (Filter Keyboard Track +/+)
Flt KT +/– (Filter Keyboard Track +/–)
Flt KT 0/+ (Filter Keyboard Track 0/+)
Flt KT +/0 (Filter Keyboard Track +/0)
Amp KT +/+ (Amp Keyboard Track +/+)
Amp KT +/– (Amp Keyboard Track +/–)
Amp KT 0/+ (Amp Keyboard Track 0/+)
Amp KT +/0 (Amp Keyboard Track +/0)
+/+: The direction of the effect will be determined by the
sign (positive or negative) of the “Ramp Low” or “Ramp
High” setting.
+/–: The direction of the effect will be determined by the sign
of the “Ramp Low” setting, and by the opposite sign of the
“Ramp High” setting (–50 for a setting of +50, and +50 for a
setting of –50).
0/+: “Ramp Low” will have no AMS effect. The sign of the
“Ramp High” setting will determine the direction of its
effect.
+/0: The sign of the “Ramp Low” setting will determine the
direction of its effect. “Ramp High” will have no AMS effect.
X50: M.Whl&AT/2
microX: JS+Y&AT/2 (Joy Stick +Y & After Touch/2)
X50: The effect is applied by [MOD] wheel movement in
the “up” direction and by aftertouch received from the MIDI
IN or USB connector. In this case, the aftertouch will pro-
duce half of the specified intensity
microX: The effect is applied by joystick +Y (up) move-
ment and by aftertouch received from the MIDI IN/USB
connector. In this case, the aftertouch will produce half of
the specified intensity.
JS–Y&AT/2 (Joy Stick–Y & After Touch/2)
X50: The effect is applied by CC#02 and by aftertouch
received from the MIDI IN/USB connector. In this case, the
aftertouch will produce half of the specified intensity.
microX: The effect is applied by joystick –Y (down) move-
ment, and by aftertouch received from the MIDI IN/USB
connector. In this case, the aftertouch will produce half of
the specified intensity.
Pedal #04 (Foot Pedal: CC#04)
If you wish to use the assignable foot pedal as an AMS, set
“Foot Pedal Assign” (GLOBAL 0–3a) to Foot Pedal (CC#04)
(☞p.165 “Foot Pedal Assign”).
A foot controller etc. connected to the ASSIGNABLE PEDAL
jack will control the effect.
KnobM1#17 (Knob Mod1: CC#17)
KnobM2#19 (Knob Mod2: CC#19)
KnobM3#20 (Knob Mod3: CC#20)
KnobM4#21 (Knob Mod4: CC#21)
If you wish to use a REALTIME CONTROLS knob [1]–[4] as
an AMS, make settings in program, combination, or multi
set to set the Ctrls tab parameter “Knobs B Assign” to the
following settings respectively: “Knob1-B” to Knob Mod.1
(CC#17), “Knob2-B” to Knob Mod.2 (CC#19), “Knob3–B” to
Knob Mod.3 (CC#20), or “Knob4-B” to Knob Mod.4
(CC#21). (☞p.162 “Knob 1...4 B Assign”)
When you set REALTIME CONTROLS to B-mode and oper-
ate knobs [1]–[4], the specified modulation will apply.
If AMS intensity is set to a positive (+) value, moving the
knob to the 12 o’clock position will produce an AMS effect of
0. Rotating the knob toward the right will produce a positive
change in the effect, and rotating it toward the left will pro-
duce a negative change. (With negative (–) settings, the
opposite effect will result.)
KnobM1 [+] (Knob Mod1: CC#17 [+] )
KnobM2 [+] (Knob Mod2: CC#19 [+] )
KnobM3 [+] (Knob Mod3: CC#20 [+] )
KnobM4 [+] (Knob Mod4: CC#21 [+] )
These differ from KnobM1#17–KnobM4#21 in the knob
position and direction of the effect. If AMS intensity is set to
a positive (+) value, rotating the knob to the far left will pro-
duce an AMS effect of 0. Rotating the knob toward the right
will apply an effect only in the positive direction. (With neg-
ative (–) settings, the opposite effect will result.)
SW 1 #80 (SW1 Mod.: CC#80)
SW 2 #81 (SW2 Mod.: CC#81)
X50: If you wish to use either [SW1] or [SW2] as an AMS,
make settings in the program, combination, or multi set to
set the Ctrls page parameter “SW1/2 Assign” to the follow-
ing values respectively: “SW1” to SW1 Mod.(CC#80), or
“SW2” to SW2 Mod.(CC#81) (☞p.161 “X50: SW1/2
Assign”). These are controlled by [SW1] or [SW2].
Foot SW #82 (Foot Switch: CC#82)
If you wish to use an assignable foot switch as an AMS, set
“Foot SW Assign” (GLOBAL 0–3a) to Foot SW (CC#82)
(☞p.164 “Foot Switch Assign”).
The effect will be controlled when you operate a foot switch
etc. connected to the ASSIGNABLE SWITCH jack.
Note Number
Amp
Key Low
Key High
AMS = Amp KT +/+
AMS Intensity = positive (+) value
Ramp Low
= +50
Ramp High
= +50
Depth and direction of modulation
zero
+ max
- max
example of Amp
Keyboard Track settings
AMS = Amp KT +/–
AMS Intensity = positive (+) value
Depth and direction of modulation
zero
+ max
- max
AMS = Amp KT 0/+
AMS Intensity = positive (+) value
Depth and direction of modulation
zero
+ max
- max
AMS = Amp KT +/0
AMS Intensity = positive (+) value
Depth and direction of modulation
zero
+ max
- max
To Next Page
Loading...
