1–1: Program Play
2
within a program, and provides an easy way to shape the overall character of the sound. This can
be used when you wish to adjust the sound as you play, or to make rough settings when creating
an original sound.
Edits you perform here will affect the values of the program parameters in the edit buffer. When
you select a Performance Editor function (1–1c), the Performance Editor data will be displayed in
the center right of the LCD, and you can see the value changes that result from your editing. If you
want to keep your edits, use the Program Write operation. (
☞
Basic Guide, page 23)
The Performance Editor adjusts the values that are set for the program parameters. The Perfor-
mance Editor cannot modify a value beyond the range of the program parameters. Since these
are rough edits, the balance between parameters may sometimes be affected.
If you check the Global mode “2–1a: Filter” (
☞
page 136 in this manual) parameter Enable Exclu-
sive, parameter changes will be transmitted as MIDI Exclusive messages each time you operate
the Performance Editor.
If these messages are received by another
TRINITY series
instrument (on which the Enable Exclu-
sive parameter is checked), that instrument will execute the corresponding Performance Editor
operations.
Octave [–3…0…+3]
A setting of
+1
will raise the pitch 1 octave. It is not possible to raise the pitch above 4', or to lower
the pitch below 32'.
Filter Freq. (Filter Cutoff Frequency) [–10…0…+10]
A setting of
+1
will raise the cutoff frequency value by 5.
Filter EG Int. (Filter EG Intensity) [–10…0…+10]
With a setting of
+1
, the value of the parameters that adjust the depth of modulation applied by
the Filter EG to the cutoff frequency will each be increased by 5, causing the Filter EG to have a
greater influence on the cutoff frequency.
This parameter will not change the polarity (sign) of the parameter values. For example, if the Per-
formance Editor value is set to –2, the parameter values will be decreased by 10, but if the original
parameter value is 8, the resulting parameter value will be 0 and not –2.
Amp Level [–10…0…+10]
A setting of
+1
will increase the output level value by 5, producing a louder volume.
Attack Time [–10…0…+10]
A setting of
+1
will increase the Amp EG attack time values by 5. For your reference, the LCD will
also display the attack time of the filter EG.
Release Time [–10…0…+10]
A setting of
+1
will increase the Filter EG and Amp EG release time values by 5.
Insert FX Bal. (Insert Effect Dry/FX Balance) [–10…0…+10]
A setting of
+1
will increase the value of the FX side by 5, so that the insert effect will be applied
more deeply.
Master FX Bal. (Master Effect Dry/FX Balance) [–10…0…+10]
A setting of
+1
will increase the value of the FX side by 5, so that the master effect will be applied
more deeply.
Octave Octave of Oscillator 1, 2
Filter Freq. Cutoff Freq of Filter 1A, 1B, 2A, 2B
Filter EG Int.
Filter EG Intensity of Filter 1A, 1B, 2A, 2B
Filter EG Int Mod By Velocity of Filter 1A, 1B, 2A, 2B
Alternate Modulation Intensity of Filter 1, 2
Amp Level Output Level of Amp 1, 2
Attack Time Attack Time of Amp 1, 2
Release Time
EG Release Time of Filter 1, 2
EG Release Time of Amp 1, 2
Insert FX Bal. Dry/FX Balance of Insert Effect
Master FX Bal. Dry/FX Balance of Master Effect
To Next Page
Loading...
Need help?
General
