Need help?Do you have a question about the Korg Trinity V3 and is the answer not in the manual?
General| Brand | Korg |
|---|---|
| Model | Trinity V3 |
| Category | Recording Equipment |
| Language | English |
Describes proper grounding procedures and potential risks of electric shock.
Introduces Program Edit mode and its initial page (P1).
Covers basic program settings like name, category, and oscillator mode.
Explains mono/polyphonic, legato, priority, and hold functions.
Describes various scale types and their usage.
Introduces pitch modulation for oscillator 1.
Explains how keyboard position affects pitch.
Describes ribbon controller's effect on pitch.
Details how the joystick's right movement affects pitch.
Explains joystick's left movement effect on pitch.
Describes using AMS to modulate pitch.
Explains the role of the Oscillator EG in pitch modulation.
Describes the Oscillator 1 LFO's impact on pitch modulation.
Details joystick control for pitch changes.
Explains AMS and intensity for pitch modulation.
Details alternate modulation for LFO frequency.
Lists page menu commands for OSC1 LFO.
Details routing and basic settings for filters 1A and 1B.
Describes parallel, serial, single, and thru routing for filters.
Details filter type and cutoff frequency settings.
Explains trim level and resonance settings.
Details how velocity affects resonance.
Describes settings for Filter 1B.
Lists commands for writing, copying, swapping, and syncing filters.
Introduces modulation for Filter 1's cutoff frequency.
Explains keyboard tracking for cutoff frequency.
Covers joystick and aftertouch effects on cutoff.
Describes AMS for cutoff frequency modulation.
Explains how velocity affects filters.
Details intensity modulation for filters.
Describes AMS for filter modulation.
Details EG modulation for filter cutoff.
Explains LFO modulation for filter cutoff.
Lists commands for filter modulation.
Explains the Filter EG's role in modifying cutoff frequencies.
Describes Start, Attack, Break, Sustain, and Release levels.
Explains Attack, Decay, Slope, and Release times.
Explains how modulation affects EG times.
Details how velocity affects EG levels.
Covers writing, copying, swapping, and syncing EGs.
Explains the Filter 1 LFO's role in cyclic changes to cutoff frequency.
Details waveform, frequency, and offset for Filter 1 LFO.
Explains Start, KeySync, Delay, and Fade settings.
Details how Alternate Modulation affects LFO frequency.
Lists commands for the Filter 1 LFO.
Explains settings for oscillator 1 volume changes.
Describes how to set the volume of oscillator 1.
Explains modulation of volume by keyboard tracking, velocity, etc.
Details key range settings for volume tracking.
Explains ramp settings for volume changes based on key position.
Details how velocity affects volume.
Explains aftertouch's effect on volume.
Describes AMS for volume modulation.
Explains how to set send levels and pan positions.
Lists commands for writing, copying, and swapping oscillator settings.
Describes how to identify and name patterns.
Explains metronome, quantization, and data removal settings.
Covers memory status, step recording, event edit, pattern parameters, and erasing.
Details commands for copying and bouncing patterns.
Explains getting data from tracks and putting patterns into tracks.
Explains specifying insert effects for timbres 1-8.
Explains effect size and enabling/disabling effects.
Covers pan, width, and send settings for effects.
Explains effect settings specific to drumkits.
Covers writing, copying, and swapping insert effects.
Explains selecting and connecting master effects.
Covers pan and return level settings.
Explains EQ settings for output tone.
Lists commands for writing and copying master effects.
Explains assigning functions to SW1 and SW2.
Explains recording and editing patterns.
Explains selecting insert effects for timbres.
Covers pan, width, and send settings for timbre effects.
Explains accessing and setting parameters for individual insert effects.
Explains track operation modes.
Explains settings for master effects and output levels.
Explains how to set parameters for master effects.
To Next Page
