Kramer VS-44DT - VS-44 DT Operation and Setup; Connecting Inputs and Outputs; Connecting Power Supply; Setting Operation Parameters via Menu

Step 7: Operate via the front panel buttons, the remote controller and via:
Web pages:
RS-232 and Ethernet:
RS-232
Baud Rate:
115,200
Parity:
None
Data Bits:
8
Command Format:
ASCII
Stop Bits:
1
Example (route the video from HDMI In 3 to Out 1):
#VID 3>1<cr>
TCP/IP Parameters
IP Address:
192.168.1.39
UDP Port #:
50000
Subnet mask:
255.255.000.000
Maximum UDP Connections:
4
Default gateway:
000.000.000.000
Maximum TCP Connections:
10
TCP Port #:
5000
Full Factory Reset
Menu
Menu-> RESET TO DEFAULT-> Change the option to YES and press Enter (to
complete the reset process you need to turn the power off and then on again)
Web Page
Go to the Device settings page and click FACTORY RESET
Protocol 3000
#FACTORY<cr> command
Step 8: Operate the VS-44DT via front panel display using the menu buttons:
To switch an input to an output:
1. Press an OUT button (1 to 4).
2. Press an IN button.
To Copy an EDID from an output to an input:
1. Press EDID.
2. Press the required OUT button.
3. Press the required IN button.
4. Press EDID.
To store the current configuration:
1. Press STO.
2. Press the required IN button to which you want to store the configuration.
3. Press STO. The current configuration is stored to the selected preset number.
To recall a preset:
1. Press RCL.
2. Press the required IN button in which the configuration is stored.
3. Press RCL. The current configuration stored in the selected preset number is
recalled.
Technical Specifications:
Inputs:
4 HDMI on HDMI connectors
5 IR on 3.5mm mini jack connectors
Outputs:
2 HDMI on HDMI connectors; 4 HDBaseT on RJ-45 connectors; 5 IR on 3.5mm mini jack connectors
1 Unbalanced stereo audio 1.3Vpp nominal (2Vrms max) / 100Ω on a 3.5mm mini jack connector
Ports:
1 Ethernet on an RJ-45 connector 1 Program on a USB connector;
1 RS-232 control on a 3-pin terminal block; 1 RS-232 data on a 3-pin terminal block
Maximum Data Rate:
10.2Gbps (3.4Gbps per graphic channel)
Supported Resolutions:
Up to 4K@60Hz (4:2:0)
HDMI Reach:
15m (49ft) @ 8bit resolution; 10m (33ft) @ 12 bit resolution
HDBaseT Reach:
100m (328ft) 4K@30Hz; 180m (590ft) 1080@60Hz@24bpp
Power Consumption:
100-240V AC 50/60Hz 38VA
Operating Temperature:
0° to +40°C (32° to 104°F)
Storage Temperature:
–40° to +70°C (–40° to 158°F)
Humidity:
10% to 90%, RHL non-condensing
Dimensions:
19” x 13.72” x 1U (W, D, H) rack mountable
Shipping Dimensions:
54.3cm x 44.2cm x 10.7cm (21.4” x 17.4” x 4.2”) W, D, H
Weight:
3.3kg (7.28lbs) approx.
Shipping Weight:
4.1kg (9.04lbs) approx.
Included Accessories:
Rack ears, 4 IR receiver cables, 4 IR emitter cables; remote control transmitter
Specifications are subject to change without notice at www.kramerav.com