Kramer VW-9 - Page 50

Kramer Electronics Ltd.
VW-9 – Protocol 3000
48
Function
Description
Syntax
Parameters/Attributes
Example
PROT-VER?
Get device protocol
version.
COMMAND
#PROT-VER?<CR>
FEEDBACK
~nn@PROT-VER3000:version<CR><LF>
version – XX.XX where X is a decimal
digit
Get the device protocol
version:
#PROT-VER?<CR>
PRST-LST?
Get saved preset list.
In most units, video
and audio presets with the
same number are stored
and recalled together by
commands #PRST-STO
and #PRST-RCL.
COMMAND
#PRST-LST?<CR>
FEEDBACK
~nn@PRST-LSTpreset,preset,…<CR><LF>
preset – Preset number
Show preset list:
#PRST-LST?<CR>
PRST-RCL
Recall saved preset list.
In most units, video
and audio presets with the
same number are stored
and recalled together by
commands #PRST-STO
and #PRST-RCL.
COMMAND
#PRST-RCLpreset<CR>
FEEDBACK
~nn@PRST-RCLpreset<CR><LF>
preset – Preset number (1 to 4)
Recall preset 1:
#PRST-RCL1<CR>
PRST-STO
Store current connections,
volumes and modes in
preset.
In most units, video
and audio presets with the
same number are stored
and recalled together by
commands #PRST-STO
and #PRST-RCL.
COMMAND
#PRST-STOpreset<CR>
FEEDBACK
~nn@PRST-STOpreset<CR><LF>
preset – Preset number (1 to 4)
Store preset 1:
#PRST-STO1<CR>
PRST-VID?
Get video connections
from saved preset.
In most units, video
and audio presets with the
same number are stored
and recalled together by
commands #PRST-STO
and #PRST-RCL.
COMMAND
#PRST-VID?preset,out<CR>
#PRST-VID?preset,*<CR>
FEEDBACK
~nn@PRST-VIDpreset,>out_id<CR><LF>
~nn@PRST-VIDpreset,in>1,in>2,in>3,…<CR><LF>
preset – Preset number – Number that
indicates the specific input:
1 – 4
> – Connection character between in and
out parameters
out_id – (1 to 4)
* for all outputs
Get video connections
from preset 3 for all
outputs:
#PRST-VID?3,*<CR>
RESET
Reset device.
To avoid locking the
port due to a USB bug in
Windows, disconnect
USB connections
immediately after running
this command. If the port
was locked, disconnect
and reconnect the cable
to reopen the port.
COMMAND
#RESET<CR>
FEEDBACK
~nn@RESETOK<CR><LF>
Reset the device:
#RESET<CR>
RESTORE
Restore data from USB
flash drive.
COMMAND
#RESTORE<CR>
FEEDBACK
~nn@RESTOREOK<CR><LF>
Restore:
#RESTORE<CR>
ROTATE
Set output rotation angle.
COMMAND
#ROTATEout_id,win_id,angle<CR>
FEEDBACK
~nn@ROTATEout_id,win_id,angle<CR><LF>
out_id – 0
win_id – 0
angle – 0 - off, 1 left 90 degree, 2 right
90 degree)
Set output rotation
angle:
#ROTATEP1,P2,P3<C
R>
ROTATE?
Get output rotation angle.
COMMAND
#ROTATE?<CR>
FEEDBACK
~nn@ROTATEout_id,win_id,angle<CR><LF>
out_id – 0
win_id – 0
angle – 0 - off, 1 left 90 degree, 2 right
90 degree)
Get output rotation
angle:
#ROTATE?<CR>
ROUTE
Set layer routing.
This command
replaces all other routing
commands.
COMMAND
#ROUTElayer,dest,src<CR>
FEEDBACK
~nn@ROUTElayer,dest,src<CR><LF>
layer – Layer Enumeration
1 – Video
2 – Audio
dest
1 – win A
2 – win B
3 – win C
4 – win D
*– ALL
src – Source id
1 – Input 1
2 – Input 2
3 – Input 3
4 – Input 4
0 – Audio Mute
Route video input 2 to
window 4:
#ROUTE1,4,2<CR>